CRS+ RestoMod

Options
123578

Comments

  • Gardenstater
    Gardenstater Posts: 4,944
    Options
    I hope you sopped up all that yoke brutha! 👀
    George / NJ

    Polk 7B main speakers, std. mods+ (1979, orig owner)
    Martin Logan Dynamo sub w/6ft 14awg Power Cord
    Onkyo A-8017 integrated
    Logitech Squeezebox Touch Streamer w/EDO applet
    iFi nano iDSD DAC
    iPurifier3
    iDefender w/ iPower PS
    Custom Steve Wilson 1m UPOCC Interconnect
    iFi Mercury 0.5m OFHC continuous cast copper USB cable
    Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
    Custom Vibration Isolation Speaker Stands and Sub Platform
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    edited June 6
    Options
    All joking aside, I did tidy up the X-over adapter. The M4 standoffs were ideal (props to @pitdogg2)
    I had to redrill the plate to move one over to an adjacent hole because the original was too close to the pin terminal plastic housing to fit the nylon nut even.

    Added damping foam front(under compression) to back (1/8" PVA) so no vibes will rear their ugly head.
    I'll simply have to drill the factory location to 5/16" so the barrel nut is self-guided thru the rear baffle....

    a67f4dqj24t8.jpg
    62juflxmklfe.jpg

    metss8cxenw6.jpg

    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • SCompRacer
    SCompRacer Posts: 9,399
    Options
    Speaking of bacon, that is hardly enough. :) I don't like to cook it inside, so I do it on the grill. I do 3 pounds with the hope of freezing some but only come in with one pound. I'm like that beggin strips dog.
    Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ * Signature Series Sonore Music Server w/Deux PS * Roon * Gustard R26 DAC / Singxer SU-6 DDC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 *
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Going to double up on my nattokinase and niacinamide.
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Another midnight run. Detoxing from all the triglycerides.
    Got one done. Had to dremel each slot corresponding to where Polk drilled each PR attachment hole. A couple were slightly off from each other. Joy...
    I can't see the black PR thru it was goal...

    tacalsb9aoua.jpg
    7qty0bvvy93x.jpg
    ifg8iikzdevr.jpg
    vj1oawr8sjib.jpg
    lmxz2zavr53m.jpg
    rdjw6wrv0d7f.jpg
    xyzlg98ck1d6.jpg
    fam2syaquucs.jpg
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • Gardenstater
    Gardenstater Posts: 4,944
    Options
    I hope you aren't forced to only play AWB Average White Band on these 🤣

    Looking forward to the Too Much Rope test.......
    George / NJ

    Polk 7B main speakers, std. mods+ (1979, orig owner)
    Martin Logan Dynamo sub w/6ft 14awg Power Cord
    Onkyo A-8017 integrated
    Logitech Squeezebox Touch Streamer w/EDO applet
    iFi nano iDSD DAC
    iPurifier3
    iDefender w/ iPower PS
    Custom Steve Wilson 1m UPOCC Interconnect
    iFi Mercury 0.5m OFHC continuous cast copper USB cable
    Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
    Custom Vibration Isolation Speaker Stands and Sub Platform
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    That's Antique White Band material right there.
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    edited June 10
    Options
    Was on fence, so went with @VR3 suggestion for magnet attachment since I'll be listening to them with grills off most the time. Polk relied HEAVILY on the larger plastic grill pegs compression as their drilling/matching of grill holes to baffle peg centers were also not accurate.

    3/8" cylindrical neodymiums glued in countersurface by @1/8 depth so I can fill and hide them.

    Just remembered why I preferred metal shop over wood shop. A lot of prep work. I decided to give them a 1/16" round over for looks and better paint adhesion.

    gqoqwfzuvnre.jpg

    gmlbgk1tpikq.jpg

    0u2s6fkbwbs8.jpg

    5gbf8l0gcqoq.jpg

    @F1, forgot I had this tucked away from the shop speaker build years ago... Will fill in the mag holes...

    3rg93y56fycw.jpg
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • F1nut
    F1nut Posts: 52,406
    Options
    I've never used that product.
    · Share on Facebook
  • Unknown
    Unknown
    Options
    This content has been removed.
  • xschop
    xschop Posts: 5,837
    Options
    Takes a couple hours to fully dry being water based, but equivalent to bondo on hardness I remember...

    wjf6iznp4165.jpg

    While that's drying, prepping Erse inductors so there's no vibes going on as they only mount with 2 small screws...

    v962d3ucvc5w.jpg

    cqgbbueioj3f.jpg

    hwedh2dw0kch.jpg



    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Can barely see the indention of the magnets. Should only need a 2nd coat of primer then light sand and they are incognito...

    qfimvw65e08l.jpg

    2hf2q1jyqvl4.jpg

    blzskcjez4y7.jpg


    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Forgot to mention I had a bacon, egg, and cheese biscuit for breakfast. :D
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Final fill of all dimples....and 400 grit sand tomorrow then final primer....

    h7yr0san8wd6.jpg

    These little guys are heavy and can still pick up with the cross-brace and shake....

    ukvwyd6oqijz.jpg



    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • Tony M
    Tony M Posts: 12,017
    Options
    You HULK'n out? :p

    Why do you have to shake them?
    Most people just listen to music and watch movies. I EXPERIENCE them.

    “Anger is an acid that can do more harm to the vessel in which it is stored than to anything on which it is poured.”
    --Mark Twain.

    “If at first you don't succeed, then skydiving definitely isn't for you.” - Steven Wright
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    edited June 12
    Options
    Shook out the drywall crumbs and demonstrated brace/Powergrab effectiveness B)

    Not needed here, but a set of reinforcement semi-rings would only need to go left/right top of the MWs in any CRS without a brace.
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Final sand and test fitment. The 3/8" barrel neodymiums are solid...
    7aaqby75pyox.jpg
    w8jyfjwcxk6v.jpg
    et7wigdsgrwf.jpg
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Think just a pint of cabinet grade paint will cover these CRS+ 2X coats? Got to stop by Sherwin Williams and get that builder's discount lol.

    lb6lo0j4whwz.jpg
    3ixk5o7jl5oa.jpg

    Wife says she wants the slight orange peel texture to match as well...Easy Peasy I say...

    7nbk3cy05ff8.jpg




    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • VR3
    VR3 Posts: 29,751
    Options
    Looking awesome

    I for one want a video of you shaking the enclosure
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Two days of prep work calls for 2 days of Bacon @pitdogg2 B)

    m2p7vnziq4hr.jpg
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    Final coat of flat-white primer just for the driver insets...

    x38d7xs5vw09.jpg

    5f88i8k5darg.jpg

    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    edited June 12
    Options
    Found 1/4 gallon tucked away from last home touch-up. 1st coat and I like that hue....

    1eonr2qvqb9b.jpg
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    edited June 12
    Options
    I think a Megadeth sticker would set these off right. :D

    Thanks Larry. More WAF friendly than the Billet 5Jrs B)
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • Gardenstater
    Gardenstater Posts: 4,944
    Options
    You need a different Polk Audio badge that puts the letters on a strip of bacon.
    George / NJ

    Polk 7B main speakers, std. mods+ (1979, orig owner)
    Martin Logan Dynamo sub w/6ft 14awg Power Cord
    Onkyo A-8017 integrated
    Logitech Squeezebox Touch Streamer w/EDO applet
    iFi nano iDSD DAC
    iPurifier3
    iDefender w/ iPower PS
    Custom Steve Wilson 1m UPOCC Interconnect
    iFi Mercury 0.5m OFHC continuous cast copper USB cable
    Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
    Custom Vibration Isolation Speaker Stands and Sub Platform
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    edited June 12
    Options

    VR3 wrote: »
    Looking awesome

    I for one want a video of you shaking the enclosure

    @VR3 ....While the paint's drying lol...

    https://youtube.com/shorts/6KXrbCMmJmg?feature=share

    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    2nd mag fill-in drying...

    These would be XSive...

    h8kyinav71pb.jpg
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • VR3
    VR3 Posts: 29,751
    Options
    Lol!! Love it, too funny
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on Facebook
  • F1nut
    F1nut Posts: 52,406
    Options
    Shakin' it up here boss
    · Share on Facebook
  • xschop
    xschop Posts: 5,837
    Options
    At least I didnt tie a string too it. :D
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • Gardenstater
    Gardenstater Posts: 4,944
    edited June 13
    Options
    https://www.youtube.com/shorts/rKn8zdaTet8
    George / NJ

    Polk 7B main speakers, std. mods+ (1979, orig owner)
    Martin Logan Dynamo sub w/6ft 14awg Power Cord
    Onkyo A-8017 integrated
    Logitech Squeezebox Touch Streamer w/EDO applet
    iFi nano iDSD DAC
    iPurifier3
    iDefender w/ iPower PS
    Custom Steve Wilson 1m UPOCC Interconnect
    iFi Mercury 0.5m OFHC continuous cast copper USB cable
    Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
    Custom Vibration Isolation Speaker Stands and Sub Platform
    · Share on Facebook