Okki Nokki mk2

2

Comments

  • joecoulsonjoecoulson Posts: 3,714
    msg wrote: »
    joecoulson wrote: »
    As far as the vacuum head brush, the felt gets just damp after initiating the vacuum but the dust is left behind. This is dramatically reduced by using the felt brush before the whole cleaning cycle. It means less times I need to remove the vacuum head and wipe/clean it.


    I'm not quote clear on this bit quoted above. Can you clarify?

    Yes

    Before I clean the record with the fluid/goat hair brush/vacuum, I use one of these brushes:
    ydcrtywxw2mf.jpeg

    To clean off loose dirt. This helps to keep larger debris out of the vacuum felt head.
    Make sense?
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • msgmsg Posts: 5,055
    You say the felt gets damp on the vacuum head, but the dust left behind - you mean on the record, or that it builds up on the vacuum head?

    Would the carbon fiber brush sweep help with this?
    I disabled signatures.
  • SCompRacerSCompRacer Posts: 7,194
    edited August 2018
    My preference is Mofi brushes. To satisfy OCD I use one for scrub and one for rinse. I also have a couple different vacuum wands for wash vacuum and rinse vacuum. I swap the cork mat for the cleaned side of LP. I use Mofi sleeves.

    Before play I do a carbon fiber brush before dropping the needle. I avoid Cheetos and pizza rolls when handling records.

    I use a Tergitol/distilled mix to clean, distilled to rinse. I'll steam nasty ones, but you gotta be careful and keep moving with the steam or you'll warp the record. Steam won't fix a damaged record though, but it helps moisten and dislodge dried, stuck on biological whatever.

    Stanton makes a convex brush with holder. I got this with a purchase but never used it. Unsure if they offer replacement pads like the Mofi's do.

    xt3zfdkbrv7z.jpg


    82dnr7pqq4ax.jpg




    Make yourself necessary to someone. Ralph Waldo Emerson

    Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ & Pro 11+ * Signature Series Sonore Music Server w/Deux PS* Twisted Pear Buffalo III Dual Mono ESS Sabre32 DAC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 *

  • joecoulsonjoecoulson Posts: 3,714
    msg wrote: »
    You say the felt gets damp on the vacuum head, but the dust left behind - you mean on the record, or that it builds up on the vacuum head?

    Would the carbon fiber brush sweep help with this?
    It helps to reduce build up on the vacuum head. Otherwise if you take a really dirty record, all the dust and dirt goes on the felt of the vacuum head.
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • joecoulsonjoecoulson Posts: 3,714
    SCompRacer wrote: »

    I avoid Cheetos and pizza rolls when handling records.



    Lol. I avoid them at all times. Awful tasting things.
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • txcoastal1txcoastal1 Posts: 10,655
    edited August 2018
    joecoulson wrote: »
    SCompRacer wrote: »

    I avoid Cheetos and pizza rolls when handling records.



    Lol. I avoid them at all times. Awful tasting things.

    FYI, the original pizza rolls in the 80's were good. I hadn't eaten them since...until about 6 months ago my son had bought a bag...whollytastelikeshlt...yup
    Post edited by KennethSwauger on
    2-channel: Modwright KWI-200 Integrated, Dynaudio C1-II Signatures
    Desktop rig: LSi7, Polk 110sub, Dayens Ampino amp, W4S DAC/pre, Sonos, JRiver
    Gear on standby: Melody 101 tube pre, Unison Research Simply Italy Integrated
    Gone to new homes: (Matt Polk's)Threshold Stasis SA12e monoblocks, Pass XA30.5 amp, Usher MD2 speakers, Dynaudio C4 platinum speakers, Modwright LS100 (voltz), Simaudio 780D DAC
  • halohalo Posts: 5,280
    SCompRacer wrote: »
    My preference is Mofi brushes. To satisfy OCD I use one for scrub and one for rinse. I also have a couple different vacuum wands for wash vacuum and rinse vacuum. I swap the cork mat for the cleaned side of LP. I use Mofi sleeves.

    Before play I do a carbon fiber brush before dropping the needle. I avoid Cheetos and pizza rolls when handling records.

    I use a Tergitol/distilled mix to clean, distilled to rinse. I'll steam nasty ones, but you gotta be careful and keep moving with the steam or you'll warp the record. Steam won't fix a damaged record though, but it helps moisten and dislodge dried, stuck on biological whatever.

    Stanton makes a convex brush with holder. I got this with a purchase but never used it. Unsure if they offer replacement pads like the Mofi's do.

    xt3zfdkbrv7z.jpg


    82dnr7pqq4ax.jpg




    That's good stuff right there! Thanks for sharing the knowledge Rich!
  • SCompRacerSCompRacer Posts: 7,194
    edited August 2018
    txcoastal1 wrote: »

    FYI, the original pizza rolls in the 80's were good. I hadn't eaten them since...until about 6 months ago my son had bought a bag...whollytastelikeshlt...yup

    I agree!
    halo wrote: »

    That's good stuff right there! Thanks for sharing the knowledge Rich![/quote]

    OCD is good for some things.....lol
    Make yourself necessary to someone. Ralph Waldo Emerson

    Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ & Pro 11+ * Signature Series Sonore Music Server w/Deux PS* Twisted Pear Buffalo III Dual Mono ESS Sabre32 DAC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 *

  • agfrostagfrost Posts: 2,275
    SCompRacer wrote: »
    My preference is Mofi brushes. To satisfy OCD I use one for scrub and one for rinse.

    To satisfy Rich's OCD I also use one Mofi brush to wash, the other to rinse.
    Jay
    SDA 2BTL * Musical Fidelity A5cr amp * Marantz DV-9500 * Modded Adcom GDA-600 DAC * Rythmik F8
    Micro Seiki DQ-50 * A hodgepodge of cabling * Belkin PF60
    Preamp rotation: Krell KSL (SCompRacer recapped) * Manley Shrimp * PS Audio 5.0
  • SCompRacerSCompRacer Posts: 7,194
    agfrost wrote: »

    To satisfy Rich's OCD I also use one Mofi brush to wash, the other to rinse.

    I love being an enabled enabler... B)
    Make yourself necessary to someone. Ralph Waldo Emerson

    Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ & Pro 11+ * Signature Series Sonore Music Server w/Deux PS* Twisted Pear Buffalo III Dual Mono ESS Sabre32 DAC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 *

  • DSkipDSkip Posts: 16,283
    This thread just reminds me why I don't want to get into vinyl.
  • SCompRacerSCompRacer Posts: 7,194
    edited August 2018
    DSkip wrote: »
    This thread just reminds me why I don't want to get into vinyl.

    I never got out so I didn't have to get back in.... B)

    Make yourself necessary to someone. Ralph Waldo Emerson

    Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ & Pro 11+ * Signature Series Sonore Music Server w/Deux PS* Twisted Pear Buffalo III Dual Mono ESS Sabre32 DAC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 *

  • Tony MTony M Posts: 8,370
    edited August 2018
    I still have my first turntable installed in a home made upright audio cabinet I built out of solid Clear Fir wood.

    In fact, I just showed it to one of my old friends yesterday.

    His word...SWEET!

    I still have every record I bought or ordered from Columbia house records mail order club.

    The good ol' days. :)

    Most people just listen to music and watch movies. I EXPERIENCE them.
  • joecoulsonjoecoulson Posts: 3,714
    DSkip wrote: »
    This thread just reminds me why I don't want to get into vinyl.
    Give it time. A lot of time! Whew
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • DSkipDSkip Posts: 16,283
    joecoulson wrote: »
    DSkip wrote: »
    This thread just reminds me why I don't want to get into vinyl.
    Give it time. A lot of time! Whew

    Actually, the financial obligation is what scares me most at this point. I know what it would cost me to feel like I'm playing at the level I should be and that is... insurmountable at this point.
  • joecoulsonjoecoulson Posts: 3,714
    Looking at your sig, I would have to agree with you:
    however I would love to see one of these in your setup:
    xrw7k6yigu7y.png
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • audioluvraudioluvr Posts: 1,441
    edited September 2018
    joecoulson wrote: »
    (why goat hair?)

    14 yr old virgin pubic hair was their first choice but after getting the restraining order, opted for the goat hair

    Home System:
    SDA 1C's - Full mod with the help by Dave...
    1000 Va Dreadnought- w/ WireWorld Mini-Eclipse cables
    WireWorld Mini-Eclipse 7 speaker cables
    WireWorld Silver Eclipse IC's
    Cambridge Audio Azur 851N - DAC/Streamer
    In The Market For A New Pre...
    B&K M200 Sonata Monoblocks
    BLE-Design 16mm Power Cables
    Denon DVD 2900

    Barn system:
    SDA SRS 2.3's Full mod done by myself
    Carver C-1 pre
    Carver M1.5t
    BluDenso - Bluetooth receiver/DAC
  • joecoulsonjoecoulson Posts: 3,714
    Uh okki nokki then...
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • SCompRacerSCompRacer Posts: 7,194
    DSkip wrote: »

    Actually, the financial obligation is what scares me most at this point. I know what it would cost me to feel like I'm playing at the level I should be and that is... insurmountable at this point.

    Sweet jebus, how much are you talking about? :o
    Make yourself necessary to someone. Ralph Waldo Emerson

    Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ & Pro 11+ * Signature Series Sonore Music Server w/Deux PS* Twisted Pear Buffalo III Dual Mono ESS Sabre32 DAC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 *

  • joecoulsonjoecoulson Posts: 3,714
    My guess is that if Skip were to venture down the rabbit hole, initial setup would run $20k+
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • halohalo Posts: 5,280
    joecoulson wrote: »
    My guess is that if Skip were to venture down the rabbit hole, initial setup would run $20k+

    That's a heck of a starter system!

    Why not grab a preowned/vintage Technics in decent shape (@mhardy6647 can make a suggestion or may even have a suitable candidate amongst his collection), a Schiit Mani, and a Nagaoka MP-110? That's not expen$ive but it'll sound pretty darn good for a minimum investment.

    Ya, you'll need something to clean the records (you can start with a Spin Clean), store the records (Mofi sleeves), a brush to wipe the records before play (Hunt EDA), and a stylus cleaner for before and after play (Mr. Clean Magic Eraser, or a stylus brush, or some AT liquid cleaner, or the Onzow).

    Still, not a huge investment to get really good quality playback for the investment and a good way for you to see if you really like it (and want to invest the time and energy on a regular basis).
  • joecoulsonjoecoulson Posts: 3,714
    I know we are way off topic, but it’s my thread so fak it.
    I think my perfect setup would be a VPI scout, Nagaoka mp500 and keep my CA phono pre.
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • joecoulsonjoecoulson Posts: 3,714
    So I have to be close to the 500th cleaning for this machine between myself and two others I have let use it. Still does a fantastic job

    Before
    pc9gaoqnk16u.jpeg


    After
    udo2zg7scfm1.jpeg
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • verbverb Posts: 8,208
    Just read this thread. Ugh. Cleaning records! I love vinyl, but am a bit too lazy right now! Great review and update Joe! :smile:
    Basement: Polk SDA SRS, Cary SLP-05 Pre, Enlightened Audio Designs CD Transport, Northstar Designs Excelsio DAC, Silnote Morpheus Ref2 Digital Cable, Marantz SA-14 SACD, McIntosh MC300 Amp, Furman 15PFi Power Conditioner, Pangea Power Cables, Wireworld Oasis 8 RCA IC's, MIT Shotgun S3 IC's, MIT Shotgun S1 Bi-Wire speaker cables
    Office: PC, EAR Acute CD Player, EAR 834L Pre, PASS ACA Monoblocks, Denon UDR-F10 Cassette, Acoustic Technologies Classic FR Speakers, SVS SB12 Plus sub, MIT AVt2 speaker cables, IFI Purifier2, AQ Cinnamon USB cable, Groneberg Quatro Reference IC's
    Spare Room: , Antique Sound Labs Wave AV-8 Monoblocks, Tisbury Mini Passive Pre, Tjoeb 99 tube CD player (modified Marantz CD-38), Analysis Plus Oval 9's, Zu Jumpers, AudioEngine B1 Streamer, Klipsch RB-61 v2, SVS PB1000 sub, Blue Jeans RCA IC's
    Living Room: Peachtree Nova Integrated, Cambridge CXN v2 Streamer, Furman 15PFi Power Conditioner, Polk RT265 In Wall Speakers, Polk DSW Pro 660wi sub
  • nooshinjohnnooshinjohn Posts: 21,582
    DSkip wrote: »
    This thread just reminds me why I don't want to get into vinyl.

    You are leaving money (a LOT of it) on the table as a hifi dealer by not offering vinyl. The markup on cartridges alone is stupid. Local dealer here told me his margins on turntables and related stuff is much higher than on anything else in his store.
    The Gear... Carver "Statement" Mono-blocks, TriangleArt Reference SE with Pass Labs Xono Phono Preamp, Walker Precision Motor Drive, ClearAudio Goldfinger Diamond v2 cartridge and Origin Conquerer Mk3c tonearm, Polk Audio "Signature" Reference Series 1.2TL with complete mods, Pass Labs X0.2 three chassis preamp, PS Audio PerfectWave DAC MkII, Pioneer Elite SC-LX701, Oppo UDP-205 4K Blu-ray player, Sony XBR70x850B 4k, Polk audio AB700/800 "in-wall" surrounds.

    Saying that it's "too hard" to pursue your dreams is no different than admitting to yourself that you are too lazy to achieve them.

    “If it moves, tax it. If it keeps moving, regulate it. And if it stops moving, subsidize it.”
  • ThortonThorton Posts: 1,248
    Every time I heard a snap, crackle or pop at Axpona it made my skin crawl. I’ll stick with digital.

    Nice review Joe. Enjoy!
    _____________________________________________________________________________________________
    Source: Roon via ethernet to DAC interface
    DAC: Bricasti M1SE
    Pre/Pro: Marantz AV8805
    Tube Preamp Buffer: Tortuga TPB.V1
    Amp1: W4S MC-5, AMP2: W4S MMC-7
    Front: Salk SoundScape 8's, Center: Salk SoundScape C7
    Surround: Polk FXIA6, Surround Back: Polk RTIA9, Atmos: Polk 70-RT
    Subs: 2 - Rythmik F25's
    IC & Speaker Cables: Acoustic Zen, Wireworld, Signal Cable
    Power Cables: Acoustic Zen, Wireworld, PS Audio
    Room Treatments: GIK Acoustics
  • joecoulsonjoecoulson Posts: 3,714
    Pops and clicks don’t bother me. As long as they are not embedded dust. Love me some vinyl. Best sounding format I own.
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
  • nooshinjohnnooshinjohn Posts: 21,582
    There is always the Sugar Cube.
    The Gear... Carver "Statement" Mono-blocks, TriangleArt Reference SE with Pass Labs Xono Phono Preamp, Walker Precision Motor Drive, ClearAudio Goldfinger Diamond v2 cartridge and Origin Conquerer Mk3c tonearm, Polk Audio "Signature" Reference Series 1.2TL with complete mods, Pass Labs X0.2 three chassis preamp, PS Audio PerfectWave DAC MkII, Pioneer Elite SC-LX701, Oppo UDP-205 4K Blu-ray player, Sony XBR70x850B 4k, Polk audio AB700/800 "in-wall" surrounds.

    Saying that it's "too hard" to pursue your dreams is no different than admitting to yourself that you are too lazy to achieve them.

    “If it moves, tax it. If it keeps moving, regulate it. And if it stops moving, subsidize it.”
  • NotaSuvNotaSuv Posts: 2,715
    edited April 20
    Fantastic review, my son had this on his I want list and after sending him your review he is ready to pull the trigger...wish the pro reviews were as in depth as yours...
  • joecoulsonjoecoulson Posts: 3,714
    Why Thank You brother
    Auralic Vega G1/Rega TT/Denon SACD - Parasound P6 - PS Audio M700x2 - Elac Adante AF-61 - AQ Niagara 5000 - SVS SB16u
Sign In or Register to comment.

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!