The 1.2TL, Project Monolith

Options
1…789101113»

Comments

  • ptrooper
    ptrooper Posts: 837
    edited November 10
    Options
    This is quick and simple ,they will be completely inert, Ai told me so :D Best to run it past the site Engineer @Gardenstater
    VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable, <3 ,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it!
  • xschop
    xschop Posts: 5,919
    Options
    What about the Unknown engineer?
    Surely he knows or has knowledge of all things inert.
    Don't take experimental gene therapies from known eugenicists.
  • Gardenstater
    Gardenstater Posts: 4,990
    Options
    I don't think the heat shrink would do much to lower the resonant frequency from around 2.2 kHz. It might lower it maybe 3% to 6% mostly from the small additional mass. It won't effect the flexural rigidity much at all.

    The adhesive layer will add a small amount of damping, but the resonant frequency is still well above any of the standing wave modes in that enclosure so it shouldn't really be an issue.
    George / NJ

    Polk 7B main speakers, std. mods+ (1979, orig owner)
    Martin Logan Dynamo sub w/6ft 14awg Power Cord
    Onkyo A-8017 integrated
    Logitech Squeezebox Touch Streamer w/EDO applet
    iFi nano iDSD DAC
    iPurifier3
    iDefender w/ iPower PS
    Custom Steve Wilson 1m UPOCC Interconnect
    iFi Mercury 0.5m OFHC continuous cast copper USB cable
    Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
    Custom Vibration Isolation Speaker Stands and Sub Platform
  • ptrooper
    ptrooper Posts: 837
    Options
    Thanks @Gardenstater ,I'll try not to overthink it , do it once ,do it right. I like OVERKILL .
    VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable, <3 ,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it!
  • skipshot12
    skipshot12 Posts: 2,171
    edited November 11
    Options
    ptrooper wrote: »
    i56v0hmbywbq.jpeg
    Wrapping them in this should do the job! What do you think?

    Was thinking the same thing.
    Or wrap it with dynamat?
  • ptrooper
    ptrooper Posts: 837
    Options
    @skipshot12 Or both? >:) Ill look into the sleeve sizes.It would remove a little internal vibe reflectivity from the dynamite aluminium I believe.Maybe a 1/4" butyl wrap like a barber pole under the sleeve ? There's still a bit of time until they go in.
    I'm dreading shipping !
    I was looking at a Mobile fidelity cd for $ 24 and $44 shipping :s
    VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable, <3 ,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it!
  • xschop
    xschop Posts: 5,919
    Options
    I could actually fit all 20 in a medium International flat rate.

    Final glue up before they head to the land down under.

    Pound each assembled, not bad...

    0o7ingh2qae5.jpg
    fdn4kdlk0h3z.jpg
    a4oe7y58fdz6.jpg
    h0cfr2av8pw4.jpg
    Don't take experimental gene therapies from known eugenicists.
  • ptrooper
    ptrooper Posts: 837
    Options
    Can’t wait thx Rob !

    Has any one dealt with this company ? Or , is there somewhere in the states that can do?

    https://audiotechnology.dk/

    VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable, <3 ,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it!
  • ptrooper
    ptrooper Posts: 837
    Options
    Exciting stuff! When the dowels go in , I’ll be having the crossover plates and tweeter bezels
    Anodised .
    I been using AI with its free 3 daily attempts and am close but still deciding on the tweet colour , it’s the duelund cap colour!
    What do you think?
    axxss0bvn3bl.jpeg
    2zpir8p30gkk.jpeg

    VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable, <3 ,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it!
  • xschop
    xschop Posts: 5,919
    Options
    The orange hue addition looks very nice.

    I never post dimensions to your plates cause they are 1-offs, but IIRC I tapped them 8-32 on the back.
    Don't take experimental gene therapies from known eugenicists.