The 1.2TL, Project Monolith
Options
Comments
-
This is quick and simple ,they will be completely inert, Ai told me so
Best to run it past the site Engineer @Gardenstater VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable,
,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it! -
What about the Unknown engineer?
Surely he knows or has knowledge of all things inert.Don't take experimental gene therapies from known eugenicists. -
I don't think the heat shrink would do much to lower the resonant frequency from around 2.2 kHz. It might lower it maybe 3% to 6% mostly from the small additional mass. It won't effect the flexural rigidity much at all.
The adhesive layer will add a small amount of damping, but the resonant frequency is still well above any of the standing wave modes in that enclosure so it shouldn't really be an issue.George / NJ
Polk 7B main speakers, std. mods+ (1979, orig owner)
Martin Logan Dynamo sub w/6ft 14awg Power Cord
Onkyo A-8017 integrated
Logitech Squeezebox Touch Streamer w/EDO applet
iFi nano iDSD DAC
iPurifier3
iDefender w/ iPower PS
Custom Steve Wilson 1m UPOCC Interconnect
iFi Mercury 0.5m OFHC continuous cast copper USB cable
Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
Custom Vibration Isolation Speaker Stands and Sub Platform -
Thanks @Gardenstater ,I'll try not to overthink it , do it once ,do it right. I like OVERKILL .VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable,
,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it! -

Wrapping them in this should do the job! What do you think?
Was thinking the same thing.
Or wrap it with dynamat? -
@skipshot12 Or both?
Ill look into the sleeve sizes.It would remove a little internal vibe reflectivity from the dynamite aluminium I believe.Maybe a 1/4" butyl wrap like a barber pole under the sleeve ? There's still a bit of time until they go in.
I'm dreading shipping !
I was looking at a Mobile fidelity cd for $ 24 and $44 shipping
VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable,
,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it! -
I could actually fit all 20 in a medium International flat rate.
Final glue up before they head to the land down under.
Pound each assembled, not bad...



Don't take experimental gene therapies from known eugenicists. -
Can’t wait thx Rob !
Has any one dealt with this company ? Or , is there somewhere in the states that can do?
https://audiotechnology.dk/
VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable,
,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it! -
Exciting stuff! When the dowels go in , I’ll be having the crossover plates and tweeter bezels
Anodised .
I been using AI with its free 3 daily attempts and am close but still deciding on the tweet colour , it’s the duelund cap colour!
What do you think?

VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable,
,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it! -
The orange hue addition looks very nice.
I never post dimensions to your plates cause they are 1-offs, but IIRC I tapped them 8-32 on the back.Don't take experimental gene therapies from known eugenicists.


