Post a picture... any picture
Options
Comments
-
-
-
Captain Kangaroo?
You know, to this day I'm still not able to slice an orange in half and then reverse it.I disabled signatures. -
... and I am still mystified by why a guy called Mr. Green Jeans wore bib overalls...
-
-
-
That is hilarious...^^^
-
Salk SoundScape 8's * Audio Research Reference 3 * Bottlehead Eros Phono * Park's Audio Budgie SUT * Krell KSA-250 * Harmonic Technology Pro 9+ * Signature Series Sonore Music Server w/Deux PS * Roon * Gustard R26 DAC / Singxer SU-6 DDC * Heavy Plinth Lenco L75 Idler Drive * AA MG-1 Linear Air Bearing Arm * AT33PTG/II & Denon 103R * Richard Gray 600S * NHT B-12d subs * GIK Acoustic Treatments * Sennheiser HD650 * -
SCompRacer wrote: »
10 miles south of me, at Carolina Beach harbor, a roofer fell off a 2 story roof, head first, and stuck in the muck of the harbor bay. Somebody saw his legs later on but it was too late. He should've been wearing one of those harnesses but sadly he didn't.Most people just listen to music and watch movies. I EXPERIENCE them. -
I saw a lot of roofers at work around Dallas. I NEVER saw one in a harness.
"The legitimate powers of government extend to such acts only as are injurious to others. But it does me no injury for my neighbour to say there are twenty gods, or no god. It neither picks my pocket nor breaks my leg." --Thomas Jefferson -
-
Well, I was told by my expert mechanic on Ford trucks of all kinds, that the bracket holding my f150 bumper probably was jarred and fell a bit from hitting a pothole. Common problem he said.
I got out some cardboard and slid under my truck to put PB Blaster on the bolts for a day or so.
Driver's side...PB Blaster applied...done. I thought it was in the original position to begin with. Like I said, I thought I slid my fingers on top of the bumper for 150 times over the years.
Passenger side....WTH?
RUSTED out bushing plate on top where the body sits on top of the frame had rusted away and the body fell down toward the bumper. The battery sits above and just to the side. Maybe the weight of Batteries sitting above the bushing helped rust it quicker than the other side which isn't that bad at all.
I looked on-line and RUST is a common thing on these frames I see. The front-end can be taken off and then the fender to get to it. There's a few things that are rusted around there too that should be replaced.
Grinding off some bolts, Welding a few new bracing / angle supports for that big bushing and it will be good to go again.
My neighbor MIGHT help me repair this by using his welding skills. I hope so anyway.
That will have to be done in the future though. 
In this picture before I replaced the light fixtures a week or two back , you can see the front-end sitting real close to the bumper. It probably happened when I hit a pothole hard on that tire under the battery in Nov or Dec. .
Most people just listen to music and watch movies. I EXPERIENCE them. -
(ASR)
-
There is nothing funnier than watching your dog eat a bumble bee.... trust me !
-
-
Post about Craigslist.
-
-
(ASR)
-
mhardy6647 wrote: »... and I am still mystified by why a guy called Mr. Green Jeans wore bib overalls...
You’re not even going mention Dancing Bear??See my profile for list of gear. -
That show was pretty creepy -- in retrospect.
-
Always loved Fred on Channel 1 and wondered how the "live animation" thing was done. Here's a link to a short explanation
https://fredsociety.com/television-freds/fred-captain-kangaroo-cartoon/
b]Beach Audio[/b]: Rega RP6 (mods) - AT33PTG/II - Parks Budgie SUT - PSAudio NPC * Eversolo DMP-A6 * Topping D90iii * Joule-Electra LA-100 mkIII * Pass Aleph 30 * MIT S3 * Polk SRS 2.3tl (mods) * PSAudio PPP3
Beach Study: Pro-Ject Stream Box S2 Ultra & Pre Box S2 * Pass ACA * DH Labs SS Q10 * Brines Folded ML-TQWT RS 40-1354 * PSA Dectet
Beach Master: WiiM Pro * Dayens Menuetto * Zu Libtec * Dynaudio Audience 50
Beach Den: Bluesound Powernode 2i * DH Labs SS Q10 * Zu Omen DWII * Richard Gray RGPC
Town Study: WiiM Pro * Chord Qute (Pardo) * Elekit TU-8600 * MIT S3 * Revel M22 * Beyer DT-990 * Shunyata Hydra 2
Town Den: Music Hall mm5.1se - Denon DL-103r - Jolida JD9ii (mods) * WiiM Pro * Cary xCiter * Rogue 99 Magnum * Schiit Aegir * MIT S3 * Polk SRS 1.2tl (mods) * Dectet * Bottlehead Crack - Senn 600
Town Porch: WiiM Pro Plus * Sunfire Sig II * Canare 4S11 * Magnepan 1.6 * Dectet -
-
as seen @ hifihaven
-
Does she grind or polish?
-
Definitely a grinder.2 channel: Anthem 225 Integrated amp; Parasound Ztuner; TechnicsTT SL1350; Vincent PHO-8 phono pre; Marantz CD6005 spinner; Polk SDA2BTL's; LAT International speaker cables, ZU Mission IC's and power cables all into a PS Audio Dectet Power center.
Other; M10 series II, M7C's, Hafler XL600 amp, RB-980BX, Parasound HCA-1500 amp , P5 preamp, all in storage. All vintage Polk have had crossover rebuilds and tweeter upgrades.
The best way to predict the future is to invent it.
It is imperative that we recognize that an opinion is not a fact.
Imagine making politics your entire personality. -
Weird, this is the same exact pose I'm usually in when listening (for amplifier buzzing).
Tickle and tease that volume knob, yeah baby!
Seen here: https://www.forbes.com/sites/marksparrow/2022/02/15/marantz-announces-new-amplifier-with-network-player-just-add-speakers/ -
I hated this ad in the Superman comic books.
"Sometimes you have to look to the past to understand where you are going in the future"
Harry / Marietta GA -
-
HT SYSTEM-
Sony 850c 4k
Pioneer elite vhx 21
Sony 4k BRP
SVS SB-2000
Polk Sig. 20's
Polk FX500 surrounds
Cables-
Acoustic zen Satori speaker cables
Acoustic zen Matrix 2 IC's
Wireworld eclipse 7 ic's
Audio metallurgy ga-o digital cable
Kitchen
Sonos zp90
Grant Fidelity tube dac
B&k 1420
lsi 9's -
