Need saw / blade recommendation

kevhed72
kevhed72 Posts: 5,046
edited May 2011 in The Clubhouse
I need to cut 6 laminated stock shelves...I imagine they are particle board under the laminate. The boards are 36" by 12", and I need to cut 3" off the length. What blade / saw do you all recommend as to keep a super-clean cut.

I own a miter saw, circular saw, and jig-saw....the miter saw will not make 1 clean cut due the blade is smaller than 12"....
???
Post edited by kevhed72 on
· Share on FacebookShare on Twitter

Comments

  • treitz3
    treitz3 Posts: 18,994
    edited May 2011
    IME, I have never had a super clean cut on particle board as it's not made for that. Not quite sure what you are asking, really...

    Circular saw I'm guessing would be my answer but a table saw would be more precise.
    ~ In search of accurate reproduction of music. Real sound is my reference and while perfection may not be attainable? If I chase it, I might just catch excellence. ~
    · Share on FacebookShare on Twitter
  • seeclear
    seeclear Posts: 1,242
    edited May 2011
    I would expect the cleanest cut with a blade with a lot of teeth, and go slow.
    "Don't forget to change your politician. They are like diapers they need to be changed regularly, and for the same reason."
    · Share on FacebookShare on Twitter
  • txcoastal1
    txcoastal1 Posts: 13,262
    edited May 2011
    Tape down your cut area with painters tape helps keep laminate intact on the bottom side of the cut, use a fine tooth blade
    2-channel: Modwright KWI-200 Integrated, Dynaudio C1-II Signatures
    Desktop rig: LSi7, Polk 110sub, Dayens Ampino amp, W4S DAC/pre, Sonos, JRiver
    Gear on standby: Melody 101 tube pre, Unison Research Simply Italy Integrated
    Gone to new homes: (Matt Polk's)Threshold Stasis SA12e monoblocks, Pass XA30.5 amp, Usher MD2 speakers, Dynaudio C4 platinum speakers, Modwright LS100 (voltz), Simaudio 780D DAC

    erat interfectorem cesar et **** dictatorem dicere a
    · Share on FacebookShare on Twitter
  • greyford1979
    greyford1979 Posts: 749
    edited May 2011
    Also tape the cuts that you will be making and it will help keep the laminate from chipping. I always do this when cutting veneered ply and does the trick to keep it from chipping:biggrin: oops I guess I was too late:redface:
    I love animals, they're delicious!
    · Share on FacebookShare on Twitter
  • kevhed72
    kevhed72 Posts: 5,046
    edited May 2011
    Thanks folks...this is one of the last steps in a custom shelf unit for HT room.
    Here's the link to when the project started:

    http://www.polkaudio.com/forums/showthread.php?t=114645

    The shelves are going in the cubby in the first pic:smile:
    · Share on FacebookShare on Twitter
  • DON73
    DON73 Posts: 516
    edited May 2011
    kevhed72 wrote: »
    I need to cut 6 laminated stock shelves...I imagine they are particle board under the laminate. The boards are 36" by 12", and I need to cut 3" off the length. What blade / saw do you all recommend as to keep a super-clean cut.

    I own a miter saw, circular saw, and jig-saw....the miter saw will not make 1 clean cut due the blade is smaller than 12"....
    ???




    A circular saw with a fine (many) tooth blade. You'll need to clamp a guide on the shelf material for the saw to rest against.
    TO ERR IS HUMAN. TO FORGIVE IS CANINE.
    · Share on FacebookShare on Twitter
  • gdb
    gdb Posts: 6,012
    edited May 2011
    Try a triple chip blade on your circ saw using a guide/fence to run the saw's shoe against. P.S. 71/4" triple chip blades are rarer than 9-10-12s the one below is a little expensive but will give the best possible cut with a hand held saw.

    http://www.amazon.com/Oldham-725P7260-4-Inch-Carbide-Surface/dp/B000LOIK0C/ref=sr_1_fkmr0_1?ie=UTF8&qid=1304881085&sr=1-1-fkmr0
    · Share on FacebookShare on Twitter
  • TNRabbit
    TNRabbit Posts: 2,168
    edited May 2011
    txcoastal1 wrote: »
    Tape down your cut area with painters tape helps keep laminate intact on the bottom side of the cut, use a fine tooth blade
    greyford1979 wrote: »
    Also tape the cuts that you will be making and it will help keep the laminate from chipping. I always do this when cutting veneered ply and does the trick to keep it from chipping:biggrin: oops I guess I was too late:redface:
    DON73 wrote: »
    A circular saw with a fine (many) tooth blade. You'll need to clamp a guide on the shelf material for the saw to rest against.
    gdb wrote: »
    Try a triple chip blade on your circ saw using a guide/fence to run the saw's shoe against. P.S. 71/4" triple chip blades are rarer than 9-10-12s the one below is a little expensive but will give the best possible cut with a hand held saw.

    http://www.amazon.com/Oldham-725P7260-4-Inch-Carbide-Surface/dp/B000LOIK0C/ref=sr_1_fkmr0_1?ie=UTF8&qid=1304881085&sr=1-1-fkmr0

    Ditto to the above.

    In my experience, you get the cleanest cut by cutting from the bottom so the saw teeath are coming UP into the taped laminate side.
    TNRabbit
    NO Polk Audio Equipment :eek:
    Sunfire TG-IV
    Ashly 1001 Active Crossover
    Rane PEQ-15 Parametric Equalizers x 2
    Sunfire Cinema Grand Signature Seven
    Carver AL-III Speakers
    Klipsch RT-12d Subwoofer
    · Share on FacebookShare on Twitter
  • seeclear
    seeclear Posts: 1,242
    edited May 2011
    txcoastal1 wrote: »
    Tape down your cut area with painters tape helps keep laminate intact on the bottom side of the cut, use a fine tooth blade
    DON73 wrote: »
    A circular saw with a fine (many) tooth blade. You'll need to clamp a guide on the shelf material for the saw to rest against.

    Yeah, FINE tooth, that is what I was trying to say!:wink:
    "Don't forget to change your politician. They are like diapers they need to be changed regularly, and for the same reason."
    · Share on FacebookShare on Twitter
  • FTGV
    FTGV Posts: 3,649
    edited May 2011
    Thin kerf 60 or 80 tooth.
    · Share on FacebookShare on Twitter
  • jamesfreak9
    jamesfreak9 Posts: 2
    kevhed72 wrote: »
    I need to cut 6 laminated stock shelves...I imagine they are particle board under the laminate. The boards are 36" by 12", and I need to cut 3" off the length. What blade / saw do you all recommend as to keep a super-clean cut.

    I own a miter saw, circular saw, and jig-saw....the miter saw will not make 1 clean cut due the blade is smaller than 12"....
    ???

    Buddy i think rip saw will be best in this case for you as it make a rip cut across the wood.

    And we can use these blades to cut the wood across the surface and over the stock.

    Your 6 laminated stock shelves can be cut down by rip saw.

    If you are good in woodworking then you can make super-clean cut using it.
    you can check this blog to get idea about Buying guide before purchasing it.

    Best regards
    · Share on FacebookShare on Twitter
  • audioluvr
    audioluvr Posts: 5,574
    Jamesfreak9 reported.
    Gustard X26 Pro DAC
    Belles 21A Pre modded with Mundorf Supreme caps
    B&K M200 Sonata monoblocks refreshed and upgraded
    Polk SDA 1C's modded / 1000Va Dreadnaught
    Wireworld Silver Eclipse IC's and speaker cables
    Harman Kardon T65C w/Grado Gold. (Don't laugh. It sounds great!)

    There is about a 5% genetic difference between apes and men …but that difference is the difference between throwing your own poo when you are annoyed …and Einstein, Shakespeare and Miss January. by Dr. Sardonicus
    · Share on FacebookShare on Twitter
  • invalid
    invalid Posts: 1,362
    FTGV wrote: »
    Thin kerf 60 or 80 tooth.

    This is what I used to cut countertops and cut it from the bottom with a circular saw. I usually clamp a board with some scrap boards to the bottom so the base of the saw has something to ride against for a straight cut.
    · Share on FacebookShare on Twitter
  • TEAforONE
    TEAforONE Posts: 1,026
    If you go the circular saw route,use a carbide tooth blade. 60-80 tooth as mentioned above,and use the painters tape as well.
    See my profile for list of gear.
    · Share on FacebookShare on Twitter
  • ken brydson
    ken brydson Posts: 8,751
    You guys know this is a 9 year old thread revived by a spammer, right?
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,380
    Party pooper 😹😂

    · Share on FacebookShare on Twitter
  • msg
    msg Posts: 9,987
    Good tips though. And Kev might still be in the planning phase.
    I disabled signatures.
    · Share on FacebookShare on Twitter
  • TEAforONE
    TEAforONE Posts: 1,026
    Now I really feel silly!
    See my profile for list of gear.
    · Share on FacebookShare on Twitter
  • txcoastal1
    txcoastal1 Posts: 13,262
    https://youtu.be/0YAcoDkj_dI
    2-channel: Modwright KWI-200 Integrated, Dynaudio C1-II Signatures
    Desktop rig: LSi7, Polk 110sub, Dayens Ampino amp, W4S DAC/pre, Sonos, JRiver
    Gear on standby: Melody 101 tube pre, Unison Research Simply Italy Integrated
    Gone to new homes: (Matt Polk's)Threshold Stasis SA12e monoblocks, Pass XA30.5 amp, Usher MD2 speakers, Dynaudio C4 platinum speakers, Modwright LS100 (voltz), Simaudio 780D DAC

    erat interfectorem cesar et **** dictatorem dicere a
    · Share on FacebookShare on Twitter
  • kevhed72
    kevhed72 Posts: 5,046
    edited September 2020
    For the life of me I cannot remember what project this was....
    · Share on FacebookShare on Twitter
  • msg
    msg Posts: 9,987
    haha, looks like you started it when it was the old forum.

    Here's an adjusted link
    https://forum.polkaudio.com/discussion/114645

    Ring any bells?
    I disabled signatures.
    · Share on FacebookShare on Twitter
  • maxward
    maxward Posts: 1,570
    But I’m sure you used the right blade.
    · Share on FacebookShare on Twitter
  • kevhed72
    kevhed72 Posts: 5,046
    Ahhh. My idea at the time turned out to be a bust. I would post a current pic but the room is piled high with the hoarder/wife stuff due the flooded office. I'll update with a pic soon....
    · Share on FacebookShare on Twitter
  • audioluvr
    audioluvr Posts: 5,574
    John 1189 reported
    Gustard X26 Pro DAC
    Belles 21A Pre modded with Mundorf Supreme caps
    B&K M200 Sonata monoblocks refreshed and upgraded
    Polk SDA 1C's modded / 1000Va Dreadnaught
    Wireworld Silver Eclipse IC's and speaker cables
    Harman Kardon T65C w/Grado Gold. (Don't laugh. It sounds great!)

    There is about a 5% genetic difference between apes and men …but that difference is the difference between throwing your own poo when you are annoyed …and Einstein, Shakespeare and Miss January. by Dr. Sardonicus
    · Share on FacebookShare on Twitter