2B's Más Huevos

Options
13»

Comments

  • voltz
    voltz Posts: 5,384
    Options
    WTG B!!! you did something special!
    2 ch- Polk CRS+ * Vincent SA-31MK Preamp * Vincent Sp-331 Amp * Marantz SA8005 SACD * Project Xperience Classic TT * Sumiko Blue Point #2 MC cartridge

    HT - Polk 703's * NAD T-758 * Adcom 5503 * Oppo 103 * Samsung 60" series 8 LCD
    · Share on Facebook
  • audioluvr
    audioluvr Posts: 6,079
    Options
    doesn't Mas Huevos mean "good eggs?" WTF. I need to stay off the juice and get back to Cabo...
    Gustard X26 Pro DAC
    Belles 21A Pre Upgraded with Mundorf Supremes
    B&K M200 Sonata monoblocks refreshed and upgraded
    Polk SDA 1C's modded / 1000Va Dreadnaught
    Wireworld Silver Eclipse IC's and speaker cables
    Harman Kardon T65C w/Grado Gold. (Don't laugh. It sounds great!)

    There is about a 5% genetic difference between apes and men …but that difference is the difference between throwing your own poo when you are annoyed …and Einstein, Shakespeare and Miss January. by Dr. Sardonicus
    · Share on Facebook
  • xschop
    xschop Posts: 5,838
    Options
    Did you recess the magnet to plate interface on those?
    And most importantly, were they F1 approved? lol
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • westmassguy
    westmassguy Posts: 6,850
    Options
    Beautiful work!
    Home Theater/2 Channel:
    Front: SDA-2ATL forum.polkaudio.com/discussion/143984/my-2as-finally-finished-almost/p1
    Center: Custom Built forum.polkaudio.com/discussion/150760/my-center-channel-project/p1
    Surrounds & Rears: Custom Built forum.polkaudio.com/discussion/151647/my-surround-project/p1
    Sonicaps, Mills, RDO-194s-198s, Dynamat, Hurricane Nuts, Blackhole5
    Pioneer Elite VSX-72TXV, Carver PM-600, SVS PB2-Plus Subwoofer

    dhsspeakerservice.com/
    · Share on Facebook
  • xschop
    xschop Posts: 5,838
    Options
    stainless0steel2 wrote: »
    xschop wrote: »
    Didn't you make some billet tweeter plates for these? Thought you did.
    I cannot find your old posts and wanted to check how you made the outer edges where they meet at baffle. Thanks


    I can't find the thread I originally posted that in but I still have some pics. These were all Larry's idea I just machined them. They turned out sharp.

    xzekfyoa2sfz.jpg
    du45haps8jq1.jpg
    staxy10u3ggn.jpg


    I've actually got a some more upgrades for these 2B's coming down the line eventually. But I'll have to put those on the back burner until summer probably.

    I'm just seeing these on my big monitor. Did you make the backing/isulating plate out of 1-piece plastic for the magnet to inset? Thanks, Rob
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • stainless0steel2
    stainless0steel2 Posts: 193
    Options
    Yes it's one piece; I just counterbored it.
    The Night is Dark and Full of Terrors
    · Share on Facebook
  • xschop
    xschop Posts: 5,838
    Options
    Thank you. I am thinking about just using a long strip of rubberized electrical tape to insulate the coil frame wire. Yours turned out great.
    Don't take experimental gene therapies from known eugenicists.
    · Share on Facebook
  • Jazzhead
    Jazzhead Posts: 526
    Options
    I admire your attention to detail, your metalwork skills. I hope they sound as good as they look.
    · Share on Facebook