rti12s and csi5 tweeters suddenly failed

very sad day for me. just noticed my three front speakers don't have the crispness anymore. they all sounded dull. three days ago, it was just the two rti12s. now the center csi5 sounded dull too. i wonder what have caused it. my setup is yamaha cx-a5100 processor to emotiva XPA5. i am not an electrician but i have read from a thread here that it's the capacitor. he changed it with a mills capacitor. please help.

it is so unusual for all of my fronts tweeter to go bad at the same time. this is a sad day for me.
RTi12 fronts, CSi5 center, RTi4 surrounds and rear surrounds
2 pairs of OWM3 for Dolby Atmos
dual AV123 MFW-15 15 inch subwoofer
Marantz AV7702 PRE/PRO
Emotiva UPA700 7 channel amp
Emotiva XPA5 5 channel amp
HTPC windows 10 with KODI(TVADDONS)
PS4

Comments

  • nooshinjohnnooshinjohn Posts: 21,491
    Only possible answer I see is something called "clipping", which is when an amplifier is pushed beyond it's capability to control the speakers, it sends a distorted signal to them which damages the drivers, usually tweeters first.
    The Gear... Carver "Statement" Mono-blocks, TriangleArt Reference SE with Pass Labs Xono Phono Preamp, Walker Precision Motor Drive, ClearAudio Goldfinger Diamond v2 cartridge and Origin Conquerer Mk3c tonearm, Polk Audio "Signature" Reference Series 1.2TL with complete mods, Pass Labs X0.2 three chassis preamp, PS Audio PerfectWave DAC MkII, Pioneer Elite SC-LX701, Oppo UDP-205 4K Blu-ray player, Sony XBR70x850B 4k, Polk audio AB700/800 "in-wall" surrounds.

    Saying that it's "too hard" to pursue your dreams is no different than admitting to yourself that you are too lazy to achieve them.

    “If it moves, tax it. If it keeps moving, regulate it. And if it stops moving, subsidize it.”
  • jeremymarcinkojeremymarcinko Posts: 3,494
    Well if you’re lucky you just damaged your hearing and not your gear.
    But yeah clipping from playing too loud will damage the tweets. Odd that they all went at once though, I think the amp might also be suspect.
    Oh, Listen here mister. We got no way of understandin' this world. But we got as much sense of this bird flyin in the sky. Now there is a lot that bird don't know, but it don't change the fact that the world is happening to him all the same. What I am tryin to say is, is that the course of your life, well its changing, and you don't even see it- Forest Bondurant
  • pitdogg2pitdogg2 Posts: 14,683
    edited January 13
    I think the word you're looking for is "resistor" the stock can fail. That can be cause by a couple of things. Getting too hot from extended loud sessions and if course what was already said asking the amp for more of more and sending it into clipping.
    You will need to pull the binding post plates to look for brown and discolored sections on the crossover board. Now I'm not sure but some speakers you will need to unhook individual drivers first because there is not much extra wire to be able to get a good look from just pulling the binding post plate. Go slow and take pictures first if you need to take wires off.
  • jaygaxjaygax Posts: 153
    the emotiva xpa5 have a 200wpc at 8ohms rated power. i'll just have to take these to an electrician. hoping everything will get fixed. thanks for the infos everybody.
    RTi12 fronts, CSi5 center, RTi4 surrounds and rear surrounds
    2 pairs of OWM3 for Dolby Atmos
    dual AV123 MFW-15 15 inch subwoofer
    Marantz AV7702 PRE/PRO
    Emotiva UPA700 7 channel amp
    Emotiva XPA5 5 channel amp
    HTPC windows 10 with KODI(TVADDONS)
    PS4
  • F1nutF1nut Posts: 42,948
    Just about every amplifier can send clipped signals.

    Electricians are not speaker technicians.

    Mills makes resistors not capacitors.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

Sign In or Register to comment.

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!