Monitor 7B upgrades

F1nutF1nut Posts: 42,693
edited March 2017 in DIY, Mods & Tweaks
Since I decided to keep these of course I had to upgrade them. Pretty much the standard crossover mods, but with all point to point wiring. I removed the fuse and used a 4.7uf in place of the 4.5uf to compensate. I also upgraded the chassis wire and terminated them with gold plated copper fastons. In addition, I installed new binding post plates from Trey, hence the fuse removal, along with new binding posts and a full set of Larry's rings.

I noticed afer I drilled out the rivet attaching the fuse holders to the plate and removed them that the two wires coming off the holders has serious oxidation, which has to affect the performance. If you are considering upgrading your binding posts you should address this issue.

The new stuff.

mcrcbh4xhjv0.jpg

Close up.

fsr4dy5udbfq.jpg

New plates and posts.

6tlygx4hamah.jpg

This is one of the fuse holders. Pretty bad oxidation.

2xhfkfu9tpg3.jpg


I forgot to mention......I love the smell of solder at midnight.








Political Correctness'.........defined

"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


President of Club Polk

Comments

  • vmaxervmaxer Posts: 4,455
    Nice.
    Pio Elete Pro 520
    Panamax 5400-EX
    Sunfire TGP 5
    Micro Seiki DD-40 - Lyra-Dorian and Denon DL-160
    PS Audio GCPH phono pre
    Sunfire CG 200 X 5
    Sunfire CG Sig 405 X 5
    OPPO BDP-83 SE
    SDA SRS 1.2TL Sonicaps and Mills
    Ctr CS1000p
    Sur - FX1000 x 4
    SUB - SVS PB2-Plus

    Workkout room:
    Sony Bravia XBR- 32-Inch 1080p
    Onkyo TX-DS898
    GFA 555
    Yamaha DVD-S1800BL/SACD
    Ft - SDA 1C

    Not being used:
    RTi 38's -4
    RT55i's - 2
    RT25i's -2, using other 2 in shop
    LSI 15's
    CSi40
    PSW 404
  • Pretty boards. Uncle Jesse once again impresses with clean and professional work.
  • K_MK_M Posts: 1,396
    Great looking work!
    Lsi15, Lsi9, LsiC,Rta11t,M5jr+,M4,SDA 3.1TL, SDA SRS 2.3TL, Rti6....Still listing stuff, a work in progress.
    B+W-Sold
    Epos-Now gone
    Infinity-Sold
    Advent-Now gone
    Yamaha A-S801
    Yamaha RX-V377
    Yamaha RX-A860
    Yamaha RX-A3060
    Harman Kardon Hk-350i
    Harman Kardon Hk-........
    Harman Kardon PM-665
    Harman Kardon HK-775
    Pioneer.......Stereo Receiver

  • heiney9heiney9 Posts: 24,112
    Very clean, very nice!
    "Appreciation of audio is a completely subjective human experience. Measurements can provide a measure of insight, but are no substitute for human judgment. Why are we looking to reduce a subjective experience to objective criteria anyway? The subtleties of music and audio reproduction are for those who appreciate it. Differentiation by numbers is for those who do not".--Nelson Pass

    Pass Aleph 30 | EE Avant Pre | EE Mini Max Plus DAC | MIT Shotgun S3 | MIT Z P/C's | updated SDA 1C| SQ Box Touch/Welbourne Labs P/S- Tubes add soul!
  • msgmsg Posts: 4,988
    Nice, Jesse.
    What kind of wire do you like for the chassis wire upgrades?
    I disabled signatures.
  • pitdogg2pitdogg2 Posts: 14,331
    K_M wrote: »
    Great looking work!

    This guy has no idea what mediocrity is. It all been stellar that I have seen.
  • gudnoyezgudnoyez Posts: 7,021
    I will buy them, what no longer for sale? They look good nice work definitely keepers enjoy the fruits of your labor!
    Home Theater
    Parasound Halo A 31 OnkyoTX-NR838 Sony XBR55X850B 55" 4K RtiA9 Fronts CsiA6 Center RtiA3 Rears FxiA6 Side Surrounds Dual Psw 111's Oppo 105D Signal Ultra Speaker Cables & IC's Signal Magic Power Cable Technics SL Q300 Panamax MR4300 Audioquest Chocolate HDMI Cables Audioquest Forest USB Cable

    2 Channel
    Adcom 555II Vincent SA-T1 Marantz SA 15S2 Denon DR-M11 Clearaudio Bluemotion SDA 2.3tl's (Z) edition MIT Terminator II Speaker Cables & IC's Adcom 545II Adcom Gtp-450 Marantz CD5004 Technics M245X SDA 2B's, SDA CRS+

    Stuff for the Head
    JD LABS C5 Headphone Amplifier, Sennheiser HD 598, Polk Audio Buckle, Polk Audio Hinge, Velodyne vPulse, Bose IE2, Sennheiser CX 200 Street II, Sennheiser MX 365

    Shower & Off the beaten path Rigs
    Polk Audio Boom Swimmer, Polk Audio Urchin B)
  • xschopxschop Posts: 1,074
    I agree, well executed F1. I 2nd the question on wires. Also any wall foam or extra dacron that you prefer?
  • westmassguywestmassguy Posts: 6,436
    Very nice Jesse. I've recommended removing the old fuse blocks for some time. I don't compensate downstream however.
    Home Theater/2 Channel:
    Front: SDA-2ATL forum.polkaudio.com/discussion/143984/my-2as-finally-finished-almost/p1
    Center: Custom Built forum.polkaudio.com/discussion/150760/my-center-channel-project/p1
    Surrounds & Rears: Custom Built forum.polkaudio.com/discussion/151647/my-surround-project/p1
    Sonicaps, Mills, RDO-194s-198s, Dynamat, Hurricane Nuts, Blackhole5
    Pioneer Elite VSX-72TXV, Carver PM-600, SVS PB2-Plus Subwoofer
    Cables: Speaker: Furez 10/2 with GLS Locking Banana Plugs
    Interconnect: Furez 10/2 with SpeakONs
    ICs: Custom Furez by Douglas Connections
    Den:
    Bose 901 Series II Continentals Restored, Re-Built Equalizer with Elna Silmic IIs, Sonicaps, and Silver Mica Caps
    Carver CT-3 Pre, Carver C-500

    dhsspeakerservice.com/
    Exclusive Distributor of Gimpod's Custom SDA Circuit Boards

    "And keep her under 70, would you, huh? Betty likes a slow ride"
  • F1nutF1nut Posts: 42,693
    Just some nice stranded copper speaker wire, much better than stock, but nothing special.

    I though the about adding some BH5, but there's so much Dacron in there already I decided against it.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • F1nutF1nut Posts: 42,693
    Since I lost the model and serial numbers when I replaced the binding post plates I came up with the following. I laminated them before attaching with 3M double sided adhesive sheet material. I think they are happy to have their identity back.

    qwbed61pt2nu.jpg

    cs2hheiw7h20.jpg

    13clghbigciw.jpg







    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • HzTweakerHzTweaker Posts: 534
    See! What you've done there is make me want these fab speakers even more. They look great Jesse.
    2ch rig:
    Speakers: LSi9s with VR3's Fortress mods
    Preamplifier: Parasound P5
    Amplifier: Vincent SP-331
    CDP: Denon 1520
    Cables: Wireworld Equinox 7 XLR ICs, Wireworld Ultraviolet 7 USB
    Benched: Parasound A23
  • FaustinFaustin Posts: 890
    Very nice work!
  • tonyp063tonyp063 Posts: 673
    Nicely done Jesse.
    Clean. Elegant.
  • machonemachone Posts: 1,128
    Nice work Jessie :)
    Mojo Audio Illuminati v3>>Quantum Byte w/LMS>>Rpi/PiCoreplayer>> Starlight 7 USB >> Mojo Audio Mystique v2 SE>>ModWright SWL 9.0 SE Signature>>Hafler DH-500 Amp+ (Musical Concepts Fully Modded)>>
    SRS 2.3TL (Fully Modded)...SDA-1A (Fully Modded with Dimensional Tweeter Delete)
    1KVA Dreadnought
    Marantz SA 8005
    Pioneer PLX-1000 Turntable - Shure SC35C/N35X - V15III/VN35HE
    Yamaha TX-540 Tuner...Sony BDP-S570
    Sony PS4

    Separate subpanel with four dedicated 20 amp circuits.
    1. Amplification 2. Analog 3. Digital 4. Video

    "All THAT IS LOST FROM THE SOURCE IS LOST FOREVER"
  • VR3VR3 Posts: 23,425
    Looking good
    - Not Tom

    Vr3Mods.com ///// Version3Audio.com

    "No, that's silly talk. Dude, you can't possibly be this audio dumb so quit the act." - Doro
  • RicardoRicardo Posts: 10,509
    Nice I miss mine. Is @cincycat13 still around? Maybe he will sell them back to me....
    _________________________________________________
    ***\\\\\........................... My Audio Journey ............................./////***

    2008 & 2010 Football Pool WINNER
    SOPA
    Thank God for different opinions. Imagine the world if we all wanted the same woman
  • george danielgeorge daniel Posts: 11,992
    Just reading this thread makes me wanna go dig out mine
    JC approves....he told me so. (F-1 nut)
  • la2vegasla2vegas Posts: 3,671
    @cincycat13 hasn't been here in a month and a half.

    Everybody who passed on these 7's when they were offered for sale is surely regretting it now.
  • KilgoreKilgore Posts: 4
    Nice! Very clean.

    I'm thinking about upgrading my Monitor 7C's with new tweeters and a crossover rebuild. They still sound pretty good, but are around 30 years old so I figure it's time.

    Can any of you who have upgraded tell me what improvement I should expect? Compared to some nice systems I've listened to, my modest system has a bit less separation and more sibilance. Some recordings can sound a bit harsh; I think the tweeter replacement should help that by balancing out the treble.

    Thanks.
  • F1nutF1nut Posts: 42,693
    edited March 2017
    What you can expect is an overall improvevent in the sound. A broad stroke, but none the less the truth. Definitely replace those tweeters.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • ConradiclesConradicles Posts: 5,864
    Great job...A classic all around nice sounding speaker. I bet the mods paid off. Enjoy.
Sign In or Register to comment.

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!