Billet RD-0194/8 Tweeter Bezels

12346»

Comments

  • pitdogg2
    pitdogg2 Posts: 27,540
    Never liked the look after that plastic bent.
    No disagreement here!
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    Badass. I bet Megadeath never sounded so good lol
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 18,283
    xschop wrote: »
    Badass. I bet Megadeath never sounded so good lol

    It’s Deth , not Death. But I’m sure you know that!!🤣

    · Share on FacebookShare on Twitter
  • Tony M
    Tony M Posts: 11,853
    edited April 28
    I didn't... :s Now I do. ;)

    ruxnufmymggu.png
    Most people just listen to music and watch movies. I EXPERIENCE them.

    “Anger is an acid that can do more harm to the vessel in which it is stored than to anything on which it is poured.”
    --Mark Twain.

    “If at first you don't succeed, then skydiving definitely isn't for you.” - Steven Wright
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    Had no clue. My friend in HS would play hooky and watch Headbangers Ball on MTV think it was.
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    pitdogg2 wrote: »
    Never liked the look after that plastic bent.
    No disagreement here!

    If I torqued too much or too little, that original -194 I designed them from would make the nastiest sound.
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 27,540
    xschop wrote: »
    pitdogg2 wrote: »
    Never liked the look after that plastic bent.
    No disagreement here!

    If I torqued too much or too little, that original -194 I designed them from would make the nastiest sound.

    I had to super glue 2 ss washers under each screw hole to get them air tight enough yet not deform or sizzle on certain frequencies.
    · Share on FacebookShare on Twitter
  • billbillw
    billbillw Posts: 7,954
    edited April 30
    I think this is what is known as a Mandela effect?
    6yijnwn7khwf.jpg
    Same thing as Loony Tunes (not toons), JIF, not Jiffy peanut butter, etc.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    edited April 30
    They must have graduated from The Quality Learing Center.

    p0dwwr159cq4.jpg



    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    pitdogg2 wrote: »
    xschop wrote: »
    pitdogg2 wrote: »
    Never liked the look after that plastic bent.
    No disagreement here!

    If I torqued too much or too little, that original -194 I designed them from would make the nastiest sound.

    I had to super glue 2 ss washers under each screw hole to get them air tight enough yet not deform or sizzle on certain frequencies.

    That's quality manufacturing.
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 27,540
    edited April 30
    xschop wrote: »
    pitdogg2 wrote: »
    xschop wrote: »
    pitdogg2 wrote: »
    Never liked the look after that plastic bent.
    No disagreement here!

    If I torqued too much or too little, that original -194 I designed them from would make the nastiest sound.

    I had to super glue 2 ss washers under each screw hole to get them air tight enough yet not deform or sizzle on certain frequencies.

    That's quality manufacturing.

    Yea, I'm not sure why the made the stand off shorter in the RD-0xxx series, makes no sense.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    8 left from this run.
    Anyone building Monoliths?
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 52,138
    pitdogg2 wrote: »
    xschop wrote: »
    pitdogg2 wrote: »
    xschop wrote: »
    pitdogg2 wrote: »
    Never liked the look after that plastic bent.
    No disagreement here!

    If I torqued too much or too little, that original -194 I designed them from would make the nastiest sound.

    I had to super glue 2 ss washers under each screw hole to get them air tight enough yet not deform or sizzle on certain frequencies.

    That's quality manufacturing.

    Yea, I'm not sure why the made the stand off shorter in the RD-0xxx series, makes no sense.

    Someone didn't measure twice.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • bcwsrt
    bcwsrt Posts: 2,579
    Or, they did, but they used Tom’s ruler …

    g4vot0i8vvlz.jpeg
    Brian

    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    6 left.
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    Made 6 extra alloys plates this weekend.
    So 12 left
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    10 available.
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter
  • xschop
    xschop Posts: 5,652
    8 to go.

    PSA:
    Dont forget to use a piece of electrical tape over coil leads before installing with 4 factory magnet screws...
    and post pics when done.
    Don't take experimental gene therapies from known eugenicists.
    · Share on FacebookShare on Twitter