What did you do to your stereo rig today?
Options
Comments
-
The guys on Phoenix said to make 100% sure the trans cover was isolated electrically from chassis. I went to great travail here just to do that.Don't take experimental gene therapies from known eugenicists.
-
I guess they are recommending that to eliminate circulating currents/hum but at the expense of diminished high frequency EMI isolation. They are in opposition.
A single point ground strap rather than the double would still minimize ground loops and if you later measured residual hum or ground related noise it could always be lifted.George / NJ
Polk 7B main speakers, std. mods+ (1979, orig owner)
Martin Logan Dynamo sub w/6ft 14awg Power Cord
Onkyo A-8017 integrated
Logitech Squeezebox Touch Streamer w/EDO applet
iFi nano iDSD DAC
iPurifier3
iDefender w/ iPower PS
Custom Steve Wilson 1m UPOCC Interconnect
iFi Mercury 0.5m OFHC continuous cast copper USB cable
Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
Custom Vibration Isolation Speaker Stands and Sub Platform -
Or, if I hear any artifact/s from current configuration, I can simply remove the two rubber gaskets so the rear cover is technically making circuit with the chassis?Don't take experimental gene therapies from known eugenicists.
-
I'm already in over my head here lol. But maybe the problem with that might be that you could get a potential path for residual magnetic flux in the transformer to drive circulating currents through the chassis?George / NJ
Polk 7B main speakers, std. mods+ (1979, orig owner)
Martin Logan Dynamo sub w/6ft 14awg Power Cord
Onkyo A-8017 integrated
Logitech Squeezebox Touch Streamer w/EDO applet
iFi nano iDSD DAC
iPurifier3
iDefender w/ iPower PS
Custom Steve Wilson 1m UPOCC Interconnect
iFi Mercury 0.5m OFHC continuous cast copper USB cable
Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
Custom Vibration Isolation Speaker Stands and Sub Platform -
xschop…
Did you do the WOPL build?
My two clair bros 700’s were built by Perry from audiophoenix. -
skipshot12 wrote: »xschop…
Did you do the WOPL build?
My two clair bros 700’s were built by Perry from audiophoenix.
Indeed, so I followed Joe's advice on these matters...
I was about to give a GFA-555 the full XS treatment before the 400 magically showed up.

Don't take experimental gene therapies from known eugenicists. -
Couple small tweaks to go....



Don't take experimental gene therapies from known eugenicists. -
Very nice mate.Extremely impressed here
VR3 SDA SRS 1.2TL Duelund Monoliths+VR31000va Dreadnaught +VR3 MM2 SDA cable,
,Lumin u2x ,<-sfp fibre <-LHYas8 Pro+ Switch,Transparent Reference MM2 xlr,power and speaker cables.FTA Sinope SE usb.40 Amp power line for amp with earth stake&Faraday shield ,20 Amp power line for digital equipment ->shunyata 8 venom power board...Working on it! -
Long overdue clean and rewire





-
After shots
Also raised TV 8”




-
@joecoulson Nice job tying up the cables! It looks nice and clean. The only critique I have is that power cables and signal cables should never be dressed in parallel runs or bundled closely together. I'd run the power cables along the bottom of the back panel and the signal cables where you currently have them.Enjoying the journey while never attaining the destination.
-
Nothing like tearing everything down, cleaning everything and putting it back together... Almost like washing a car- Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
-
I desperately need to do this to both my upstairs TV system and for my basement theater setup. As components were added and taken away over the last 5 years, the cable routing became tangled and messy.
My 2ch is actually pretty clean.
-
@joecoulson Nice job tying up the cables! It looks nice and clean. The only critique I have is that power cables and signal cables should never be dressed in parallel runs or bundled closely together. I'd run the power cables along the bottom of the back panel and the signal cables where you currently have them.
XLR signal cables run with power. RCA’s not.






