Rti A9 Issue - No Highs when wired to bottom

BtrSound
BtrSound Posts: 123
edited July 2011 in Troubleshooting
I rewired my HT and I tried to wire my rtiA9's up to the bottom psots, when they ahve alwyas been hooked up to the top. When I hooked them up to the bottom post, it only played the low. Nothing came out of the highs. I hooked it back up to the top posts and I do not believe the lows are playing. Does anyone have any idea what is going on?
Post edited by BtrSound on
· Share on FacebookShare on Twitter

Comments

  • Outfitter03
    Outfitter03 Posts: 563
    edited July 2011
    Are the jumpers in place? If they are I would remove and inspect them to make sure they are not oxidized. Use a little Deoxit and Pro Gold if you have any. Then reinstall them and make sure there is a good mechanical connection.
    · Share on FacebookShare on Twitter
  • EndersShadow
    EndersShadow Posts: 17,590
    edited July 2011
    Outfitter03 wrote: »
    Are the jumpers in place? If they are I would remove and inspect them to make sure they are not oxidized. Use a little Deoxit and Pro Gold if you have any. Then reinstall them and make sure there is a good mechanical connection.

    What he said!
    "....not everything that can be counted counts, and not everything that counts can be counted." William Bruce Cameron, Informal Sociology: A Casual Introduction to Sociological Thinking (1963)
    · Share on FacebookShare on Twitter
  • george daniel
    george daniel Posts: 12,096
    edited July 2011
    ^^^^^^^^^^^^^^^yep^^^^^^^^^^^^^^^^^
    JC approves....he told me so. (F-1 nut)
    · Share on FacebookShare on Twitter
  • Tony M
    Tony M Posts: 11,151
    edited July 2011
    I love those easy fixes!!:biggrin:
    Most people just listen to music and watch movies. I EXPERIENCE them.
    · Share on FacebookShare on Twitter
  • dorokusai
    dorokusai Posts: 25,577
    edited July 2011
    Yeah, jumpers.
    CTC BBQ Amplifier, Sonic Frontiers Line3 Pre-Amplifier and Wadia 581 SACD player. Speakers? Always changing but for now, Mission Argonauts I picked up for $50 bucks, mint.
    · Share on FacebookShare on Twitter
  • tonyb
    tonyb Posts: 32,967
    edited July 2011
    Looking at the rest of the speaks in your sig., we hope you have the jumpers in place for the rest of them too. If you somehow lost them, just make some from some good quality speaker wire you may have laying around.
    HT SYSTEM-
    Sony 850c 4k
    Pioneer elite vhx 21
    Sony 4k BRP
    SVS SB-2000
    Polk Sig. 20's
    Polk FX500 surrounds

    Cables-
    Acoustic zen Satori speaker cables
    Acoustic zen Matrix 2 IC's
    Wireworld eclipse 7 ic's
    Audio metallurgy ga-o digital cable

    Kitchen

    Sonos zp90
    Grant Fidelity tube dac
    B&k 1420
    lsi 9's
    · Share on FacebookShare on Twitter
  • BtrSound
    BtrSound Posts: 123
    edited July 2011
    The jumpers are in place. Tomorrow I will take them off and check them out. Thank you
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,567
    edited July 2011
    BtrSound wrote: »
    The jumpers are in place.

    Perhaps the contact has gone south. Loosen the nuts, wiggle things around and try it again.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter