New to me 10B
MarkC568
Posts: 3
Saw these listed on CL the next town over. Auditioned in a really dark old trailer house, hooked up to an extremely tired-sounding low end 80s receiver & CD player.
Dirty and dusty, but the cabinets/vinyl were nearly mint. The half-dead amp didn't really give any indication of sound quality, all drivers appeared to work and there was no woofer rub. I have a set of 7Bs I've owned and loved since the 80s, so I pulled the trigger.
Connected them to the Dynaco, and they sound pretty good! The crossovers appear to be untouched, have stickers from '85 and '86.
My order of crossover rebuild parts arrives tomorrow, looking forward to seeing how much improvement that brings.
Dirty and dusty, but the cabinets/vinyl were nearly mint. The half-dead amp didn't really give any indication of sound quality, all drivers appeared to work and there was no woofer rub. I have a set of 7Bs I've owned and loved since the 80s, so I pulled the trigger.
Connected them to the Dynaco, and they sound pretty good! The crossovers appear to be untouched, have stickers from '85 and '86.
My order of crossover rebuild parts arrives tomorrow, looking forward to seeing how much improvement that brings.
Dynaco PAS3/ST35
Pioneer SA-5200/SA-500/PL-514
Dual 1249
Polk 7B/10B
Pioneer SA-5200/SA-500/PL-514
Dual 1249
Polk 7B/10B
Comments
-
I think they will sound better if you can pull them out into the room a bit (experiment with how much) and put them on some solid stands with mass to them to raise the acoustic center up closer to your ear height and to decouple from the wooden floor somewhat, especially if it is a suspended floor above another room and not on solid concrete. It is never good for imaging to have stuff between the speakers. Don't forget to replace those SL2000 with RD0194 when your budget allows. Order them from Polk and ask for the forum discount.George / NJ
Polk 7B main speakers, std. mods+ (1979, orig owner)
Martin Logan Dynamo sub w/6ft 14awg Power Cord
Onkyo A-8017 integrated
Logitech Squeezebox Touch Streamer w/EDO applet
iFi nano iDSD DAC
iPurifier3
iDefender w/ iPower PS
Custom Steve Wilson 1m UPOCC Interconnect
iFi Mercury 0.5m OFHC continuous cast copper USB cable
Custom Ribbon Speaker Cables, 5ft long, 4N Copper, 14awg, ultra low inductance
Custom Vibration Isolation Speaker Stands and Sub Platform -
The mailman brought my crossover rebuild parts today, so I spent the early evening rebuilding those. Back together now, the new caps need to burn in a bit, but these already sound less constrained.
I've pulled them out another foot or so, which does seem to improve imaging. A set of stands in definitely on the menu. I think I have enough oak scraps to build a set without needing to buy much more.
This room's in the basement, so there's concrete right underneath that laminate.
New tweeters on the list for sure too. I wouldn't say these are shrill, but they are a bit much.
Do you have to call Polk to order the 194s, or are they somewhere on their site?
Thanks for the guidance!
Dynaco PAS3/ST35
Pioneer SA-5200/SA-500/PL-514
Dual 1249
Polk 7B/10B -
Call Polk. You want the RD0194-1, that's a zero.Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."
President of Club Polk -
I was able to get my stands completed last night. No finish yet, as I was excited to give them a listen as soon as I had them screwed together.
I had a fair bit of red oak shorts left from a doing a lot of trim work at our previous house, so these were built for almost no cost.
They're based on the Polk stand drawing that is floating about. The base is maybe 1.5 inches shallower front-to-back which saved me gluing up an additional joint. Seems plenty stable with the 10s.
Dynaco PAS3/ST35
Pioneer SA-5200/SA-500/PL-514
Dual 1249
Polk 7B/10B -
Hey…nice job on those stands. I’ve got some 7Bs as well. I’m looking forward to your impressions on how they compare with the 10s once you get those new tweets in!FKA: anton.chigurh (see profile page)
-
Very nice job on the stands!!
Any pics of the crossovers?
