Group buy: Avel Lindberg 1000VA isolation transformers for DreadNought

Options
124

Comments

  • nspindel
    nspindel Posts: 5,343
    edited November 2012
    Options
    I had Signal Cable make me custom wires for this application. My speaker cables use bananas. So for the Dreadnaught cables, I had Frank put bananas on one side (the Dreadnaught side) and on the speaker side I put one banana and one spade. On my 4.1TL's I replaced the pin/blade connector with a single binding post. The banana goes into that binding post. The spade gets connected to the ground post, so the ground post has a banana and a spade connected to it.

    My ccgr-ss arrive tomorrow, I already have some dynamat.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Leftplumma
    Leftplumma Posts: 88
    edited November 2012
    Options
    Received my tranny today in perfect condition.
    Thanks so much Neil for helping us out with this buy.
    And also for the extra effort with the address mixup.
    You ROCK mister.
    Polk SDA 1.2 TL
    Infinity SSW-210
    Integra DTR 7.1
    Pioneer SC-57 Elite
    Sony X777ES
    Sansui BA-5000
    Hafler XL 600's in mono w/ George Kay Audio Tube upgrades
    Hafler xl 600 stock
    Krell FPB 600
    Avel 1000VA Dreadnought
    · Share on Facebook
  • EndersShadow
    EndersShadow Posts: 17,759
    edited November 2012
    Options
    Leftplumma wrote: »
    Received my tranny today in perfect condition.

    Sig material there!
    "....not everything that can be counted counts, and not everything that counts can be counted." William Bruce Cameron, Informal Sociology: A Casual Introduction to Sociological Thinking (1963)
    · Share on Facebook
  • Moose68Bash
    Moose68Bash Posts: 3,843
    edited November 2012
    Options
    Neil, I received my transformer last week and am waiting for my Dreadnought box to finish construction and install it in my system. Thanks again for doing this for all of us. Phil
    Family Room, Innuos Statement streamer (Roon Core) with Morrow Audio USB cable to McIntosh MC 2700 pre with DC2 Digital Audio Module; AQ Sky XLRs to CAT 600.2 dualmono amp, Morrow Elite Speaker Cables to NOLA Baby Grand Reference Gold 3 speakers. Power source for all components: Silver Circle Audio Pure Power One with dedicated 20 amp circuit to main panel.

    Exercise Room, Innuos Streamer via Cat 6 cable connection to PS Audio PerfectWave MkII DAC w/Bridge II, AQ King Cobra RCAs to Perreaux PMF3150 amp (fully restored and upgraded by Jeffrey Jackson, Precision Audio Labs), Supra Rondo 4x2.5 Speaker Cables to SDA 1Cs (Vr3 Mods Xovers and other mods.), Dreadnaught with Supra Rondo 4x2.5 interconnect cables by Vr3 Mods. Power for each component from dedicated 20 amp circuit to main panel, except Innuos Statement powered from Silver Circle Audio Pure Power One.

    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited November 2012
    Options
    Excellent. Glad everyone is happy!

    I just built mine tonight - Larry's case, Cardas posts, spikes, and dynamat. Sounds mint! You all are in for a treat.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited November 2012
    Options
    Mine made it as far as JFK airport in NY so far.
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited November 2012
    Options
    Don't be too sure of that. Tracking on mine was still saying electronic notice received and it showed up at my door.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited November 2012
    Options
    nspindel wrote: »
    Don't be too sure of that. Tracking on mine was still saying electronic notice received and it showed up at my door.

    That is direct from Canada Post. They haven't actually taken possession of it yet from the US for whatever reason. Got to JFK yesterday.

    I think customs is being nosey and checking the package.
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited November 2012
    Options
    Ah, ok. Forgot you're up there in the north land!
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • VR3
    VR3 Posts: 29,749
    edited December 2012
    Options
    Are there any of these available?

    Thanks
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited December 2012
    Options
    Nope, all spoken for, sorry Trey. I've got a fully assembled 800VA Dreadnaught for sale, but the 1000VA's are all taken.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • VR3
    VR3 Posts: 29,749
    edited December 2012
    Options
    What are you wanting for the 800va? I may have a buyer for you
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited December 2012
    Options
    http://www.polkaudio.com/forums/showthread.php?139176-Fully-Assembled-800VA-Dreadnaught-in-Larry-s-case

    Pics suck. Dreadnaught doesn't!
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Leftplumma
    Leftplumma Posts: 88
    edited December 2012
    Options
    EndersShadow wrote: »
    Sig material there!
    Sig material??
    Polk SDA 1.2 TL
    Infinity SSW-210
    Integra DTR 7.1
    Pioneer SC-57 Elite
    Sony X777ES
    Sansui BA-5000
    Hafler XL 600's in mono w/ George Kay Audio Tube upgrades
    Hafler xl 600 stock
    Krell FPB 600
    Avel 1000VA Dreadnought
    · Share on Facebook
  • drumminman
    drumminman Posts: 3,396
    edited December 2012
    Options
    FYI, I went from the 800VA to the 1000VA and it seemed like the 1000VA took a little longer to burn in and reach optimal sound quality. I don't have a cable cooker to pre condition it so I hooked it up and started using it.

    I was a little disappointed at first as I had grown accustomed to the improvement the smaller tranny gave, which I think burned in a little quicker. But now after several months of use the big boy produces truly stunning results, better than the smaller one.

    Be patient - you'll be rewarded!
    "Science is suppose to explain observations not dismiss them as impossible" - Norm on AA; 2.3TL's w/sonicaps/mills/jantzen inductors, Gimpod's boards, Lg Solen SDA inductors, RD-0198's, MW's dynamatted, Armaflex speaker gaskets, H-nuts, brass spikes, Cardas CCGR BP's, upgraded IC Cable, Black Hole Damping Sheet strips, interior of cabinets sealed with Loctite Power Grab, AI-1 interface with 1000VA A-L transformer
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited December 2012
    Options
    WooHoo!! My transformer was released into Canada yesterday. Stayed at Customs from the 28th till the 4th. Hope to have it by the end of next week with how slow Canada Post operates. :p
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited December 2012
    Options
    Wow, that is just insanely slow.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Leftplumma
    Leftplumma Posts: 88
    edited December 2012
    Options
    With all this chat I can't wait to hear mine!!
    I'm waiting on a few things, and looking for some cables.
    Polk SDA 1.2 TL
    Infinity SSW-210
    Integra DTR 7.1
    Pioneer SC-57 Elite
    Sony X777ES
    Sansui BA-5000
    Hafler XL 600's in mono w/ George Kay Audio Tube upgrades
    Hafler xl 600 stock
    Krell FPB 600
    Avel 1000VA Dreadnought
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited December 2012
    Options
    I can't say that I'm amazed at the difference versus the 800VA. I think it sounds great, but the 800VA did as well. But this is not broken in yet. To do a fair comparison I'd need to let this get its hours, and then start switching back and forth. But I've already sold the 800VA to Tony, so I'll just have to take it on faith that this is going to open up into a worthwhile upgrade. It sounds great already, so I'm quite optimistic.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • drumminman
    drumminman Posts: 3,396
    edited December 2012
    Options
    nspindel wrote: »
    I can't say that I'm amazed at the difference versus the 800VA. I think it sounds great, but the 800VA did as well. But this is not broken in yet. To do a fair comparison I'd need to let this get its hours, and then start switching back and forth. But I've already sold the 800VA to Tony, so I'll just have to take it on faith that this is going to open up into a worthwhile upgrade. It sounds great already, so I'm quite optimistic.

    See post #109 - I had pretty much the experience you're describing. It's a little frustrating but keep playing it. Don't be afraid to use the volume knob :cheesygrin: There's a lot of copper in this tranny and it needs some current run through it to loosen things up.

    I didn't time the hours on it until it opened up, but I'm guessing somewhere around 75-100. My memory is that the 800VA reached it's potential quicker.
    "Science is suppose to explain observations not dismiss them as impossible" - Norm on AA; 2.3TL's w/sonicaps/mills/jantzen inductors, Gimpod's boards, Lg Solen SDA inductors, RD-0198's, MW's dynamatted, Armaflex speaker gaskets, H-nuts, brass spikes, Cardas CCGR BP's, upgraded IC Cable, Black Hole Damping Sheet strips, interior of cabinets sealed with Loctite Power Grab, AI-1 interface with 1000VA A-L transformer
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited December 2012
    Options
    oh i'm never afraid to use the volume knob!
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited December 2012
    Options
    Well its here. $42 for taxes and handling. Ouch!

    Thanks again for doing this Neil!!
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited December 2012
    Options
    Looks like I spoke to soon.

    Went to the post office outlet to pick it up as I got the delivery card yesterday when they tried to deliver it.

    Well are you ready for this? They lost it! It is somewhere lost between when the driver attempted delivery yesterday and the post office outlet. No one knows where it is.

    Canada Post is investigating. Said I would know something by the 14th and if nothing, well a very complicated process of claims so I was briefly told.

    Today saw a few crappy things occur and this was the icing on that cake.
    · Share on Facebook
  • nspindel
    nspindel Posts: 5,343
    edited December 2012
    Options
    Are you joking? That's awful!

    Well, the good news, at least, is that Avel Lindberg ships it insured. So if it doesn't arrive you ought to be able to have a claim via the insurance.
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited December 2012
    Options
    nspindel wrote: »
    Are you joking? That's awful!

    I really wish I was
    · Share on Facebook
  • GlennDog
    GlennDog Posts: 3,158
    edited December 2012
    Options
    I'm sure the RCMP are on it . . . but seriously, I wish you all the best!

    G
    AC Regenerator PS Audio PerfectWave Power Plant 10
    Source Lumin U1 Mini into Lampizator Baltic 4 DAC
    Pre Cary SLP-05
    Power Rogue M180 Dark monos
    Mains Salk HT2-TL
    Rythmik F12
    · Share on Facebook
  • drumminman
    drumminman Posts: 3,396
    edited December 2012
    Options
    Drenis wrote: »
    I really wish I was

    Don't know how Canada Post Office works but here stuff occasionally gets delivered to the wrong house. I'd check up and down your street to see if it was delivered to any of your neighbors.
    "Science is suppose to explain observations not dismiss them as impossible" - Norm on AA; 2.3TL's w/sonicaps/mills/jantzen inductors, Gimpod's boards, Lg Solen SDA inductors, RD-0198's, MW's dynamatted, Armaflex speaker gaskets, H-nuts, brass spikes, Cardas CCGR BP's, upgraded IC Cable, Black Hole Damping Sheet strips, interior of cabinets sealed with Loctite Power Grab, AI-1 interface with 1000VA A-L transformer
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited December 2012
    Options
    drumminman wrote: »
    Don't know how Canada Post Office works but here stuff occasionally gets delivered to the wrong house. I'd check up and down your street to see if it was delivered to any of your neighbors.

    If that was in fact the case, I wouldn't have received a delivery notice card. It shows that they attempted delivery just after 12 Thursday. Everything about that is also recorded in the scans. It was scanned for delivery when the driver pulled up and scanned again when he put it back in the truck. Canada Post is honestly very good and this is the first incident of its kind I've ever experienced. When it comes to family and friends and commercial operations who utilize them, I've never heard of anything like this happening. So it is indeed a unique circumstance.

    Also a signature would be electronic and posted publicly on the website to show who in fact signed for it. I going to assume it was mistakenly left on the truck or the driver took it. Medium sized box, $300 value, heavy... it happens unfortunately... but those kinds of actions I would expect from other, larger companies who deliver packages... I wont name names.
    · Share on Facebook
  • Drenis
    Drenis Posts: 2,871
    edited December 2012
    Options
    Received a call from Canada Post. My parcel is at the store waiting for me...and was there the whole time! Apparently some customs paperwork was ripped off and they held the package to gather information to see if they could release it to me or not. I'm not sure I by that story and am still quite pissed about being lied too. If someone put out to have the parcel held, then tell me! State the issue and what your doing about it instead of lying to my face by saying it's not there when it really is! The postal outlet will certainly hear about that when I pick it up. My question is if the paperwork was missing or damaged, how did the driver attempt delivery within Canada Posts procedures AND request payment? Because it was clearly stated on the card there was fee's owing.

    Obviously someone f'd up and is covering up with some silly story.
    · Share on Facebook
  • Moose68Bash
    Moose68Bash Posts: 3,843
    edited December 2012
    Options
    Drenis, when you pick it up, be careful how you lift it -- no hernias or herniated disks! :wink:
    Family Room, Innuos Statement streamer (Roon Core) with Morrow Audio USB cable to McIntosh MC 2700 pre with DC2 Digital Audio Module; AQ Sky XLRs to CAT 600.2 dualmono amp, Morrow Elite Speaker Cables to NOLA Baby Grand Reference Gold 3 speakers. Power source for all components: Silver Circle Audio Pure Power One with dedicated 20 amp circuit to main panel.

    Exercise Room, Innuos Streamer via Cat 6 cable connection to PS Audio PerfectWave MkII DAC w/Bridge II, AQ King Cobra RCAs to Perreaux PMF3150 amp (fully restored and upgraded by Jeffrey Jackson, Precision Audio Labs), Supra Rondo 4x2.5 Speaker Cables to SDA 1Cs (Vr3 Mods Xovers and other mods.), Dreadnaught with Supra Rondo 4x2.5 interconnect cables by Vr3 Mods. Power for each component from dedicated 20 amp circuit to main panel, except Innuos Statement powered from Silver Circle Audio Pure Power One.

    · Share on Facebook