will any of these polyswitches work in my 2.3tl's?

Options
zarrdoss
zarrdoss Posts: 2,562
edited April 2009 in Vintage Speakers
Not having any problems yet but was wondering if any of these would work in my 2.3tl's? I was going to place a PE order soon and was going to throw some of these on here if they would work.

http://www.parts-express.com/wizards/searchResults.cfm?FTR=&search_type=main&WebPage_ID=3&searchFilter=polyswitches&x=24&y=5
· Share on Facebook

Comments

  • Unknown
    Unknown
    edited April 2009
    Options
    This content has been removed.
  • zarrdoss
    zarrdoss Posts: 2,562
    edited April 2009
    Options
    cool thanks
    · Share on Facebook
  • amulford
    amulford Posts: 5,020
    edited April 2009
    Options
    Take them out and jumper it with good quality wire. You don't need them...
    · Share on Facebook
  • inspiredsports
    inspiredsports Posts: 5,502
    edited April 2009
    Options
    amulford wrote: »
    Take them out and jumper it with good quality wire. You don't need them...

    Yes they are a huge compromise, but with all due respect I would qualify that advice.

    --- If you have clean audio sources and are reasonable about turning your volume down if you sense distortion, remove and "jumper" them.

    --- If you crank it with reckless abandon and/or have low quality sources/amps/etc., replace them.
    VTL ST50 w/mods / RCA6L6GC / TlfnknECC801S
    Conrad Johnson PV-5 w/mods
    TT Conrad Johnson Sonographe SG3 Oak / Sumiko LMT / Grado Woodbody Platinum / Sumiko PIB2 / The Clamp
    Musical Fidelity A1 CDPro/ Bada DD-22 Tube CDP / Conrad Johnson SD-22 CDP
    Tuners w/mods Kenwood KT5020 / Fisher KM60
    MF x-DAC V8, HAInfo NG27
    Herbies Ti-9 / Vibrapods / MIT Shotgun AC1 IEC's / MIT Shotgun 2 IC's / MIT Shotgun 2 Speaker Cables
    PS Audio Cryo / PowerPort Premium Outlets / Exact Power EP15A Conditioner
    Walnut SDA 2B TL /Oak SDA SRS II TL (Sonicaps/Mills/Cardas/Custom SDA ICs / Dynamat Extreme / Larry's Rings/ FSB-2 Spikes
    NAD SS rigs w/mods
    GIK panels
    · Share on Facebook
  • AudioGenics
    AudioGenics Posts: 2,567
    edited April 2009
    Options
    good info
    · Share on Facebook
  • inspiredsports
    inspiredsports Posts: 5,502
    edited April 2009
    Options
    joseph.v.chen wrote: »
    good info

    Um, yeah, . . . that's why I offered it. I'm not in the habit offering bad info.
    VTL ST50 w/mods / RCA6L6GC / TlfnknECC801S
    Conrad Johnson PV-5 w/mods
    TT Conrad Johnson Sonographe SG3 Oak / Sumiko LMT / Grado Woodbody Platinum / Sumiko PIB2 / The Clamp
    Musical Fidelity A1 CDPro/ Bada DD-22 Tube CDP / Conrad Johnson SD-22 CDP
    Tuners w/mods Kenwood KT5020 / Fisher KM60
    MF x-DAC V8, HAInfo NG27
    Herbies Ti-9 / Vibrapods / MIT Shotgun AC1 IEC's / MIT Shotgun 2 IC's / MIT Shotgun 2 Speaker Cables
    PS Audio Cryo / PowerPort Premium Outlets / Exact Power EP15A Conditioner
    Walnut SDA 2B TL /Oak SDA SRS II TL (Sonicaps/Mills/Cardas/Custom SDA ICs / Dynamat Extreme / Larry's Rings/ FSB-2 Spikes
    NAD SS rigs w/mods
    GIK panels
    · Share on Facebook
  • amulford
    amulford Posts: 5,020
    edited April 2009
    Options
    inspiredsports wrote: »
    Yes they are a huge compromise, but with all due respect I would qualify that advice.

    --- If you have clean audio sources and are reasonable about turning your volume down if you sense distortion, remove and "jumper" them.

    --- If you crank it with reckless abandon and/or have low quality sources/amps/etc., replace them.

    Excellent advice. I was hoping he already knew it...
    · Share on Facebook
  • zarrdoss
    zarrdoss Posts: 2,562
    edited April 2009
    Options
    amulford wrote: »
    Excellent advice. I was hoping he already knew it...

    I did from previous threads but after just spending $300 for new 198's and my luck I figured all the insurance I can get. Polk CS is awesome sent me 4 new ones and got them in two days! I will install when I really get bored.
    · Share on Facebook