will any of these polyswitches work in my 2.3tl's?
zarrdoss
Posts: 2,562
Not having any problems yet but was wondering if any of these would work in my 2.3tl's? I was going to place a PE order soon and was going to throw some of these on here if they would work.
http://www.parts-express.com/wizards/searchResults.cfm?FTR=&search_type=main&WebPage_ID=3&searchFilter=polyswitches&x=24&y=5
http://www.parts-express.com/wizards/searchResults.cfm?FTR=&search_type=main&WebPage_ID=3&searchFilter=polyswitches&x=24&y=5
Post edited by zarrdoss on
Comments
-
contact polk cs tomorrow. they will most likely still have them and will send them to you free of charge.The Gear... Carver "Statement" Mono-blocks, Mcintosh C2300 Arcam AVR20, Oppo UDP-203 4K Blu-ray player, Sony XBR70x850B 4k, Polk Audio Legend L800 with height modules, L400 Center Channel Polk audio AB800 "in-wall" surrounds. Marantz MM7025 stereo amp. Simaudio Moon 680d DSD
“When once a Republic is corrupted, there is no possibility of remedying any of the growing evils but by removing the corruption and restoring its lost principles; every other correction is either useless or a new evil.”— Thomas Jefferson -
cool thanks
-
Take them out and jumper it with good quality wire. You don't need them...
-
Take them out and jumper it with good quality wire. You don't need them...
Yes they are a huge compromise, but with all due respect I would qualify that advice.
--- If you have clean audio sources and are reasonable about turning your volume down if you sense distortion, remove and "jumper" them.
--- If you crank it with reckless abandon and/or have low quality sources/amps/etc., replace them.VTL ST50 w/mods / RCA6L6GC / TlfnknECC801S
Conrad Johnson PV-5 w/mods
TT Conrad Johnson Sonographe SG3 Oak / Sumiko LMT / Grado Woodbody Platinum / Sumiko PIB2 / The Clamp
Musical Fidelity A1 CDPro/ Bada DD-22 Tube CDP / Conrad Johnson SD-22 CDP
Tuners w/mods Kenwood KT5020 / Fisher KM60
MF x-DAC V8, HAInfo NG27
Herbies Ti-9 / Vibrapods / MIT Shotgun AC1 IEC's / MIT Shotgun 2 IC's / MIT Shotgun 2 Speaker Cables
PS Audio Cryo / PowerPort Premium Outlets / Exact Power EP15A Conditioner
Walnut SDA 2B TL /Oak SDA SRS II TL (Sonicaps/Mills/Cardas/Custom SDA ICs / Dynamat Extreme / Larry's Rings/ FSB-2 Spikes
NAD SS rigs w/mods
GIK panels -
good info
-
joseph.v.chen wrote: »good info
Um, yeah, . . . that's why I offered it. I'm not in the habit offering bad info.VTL ST50 w/mods / RCA6L6GC / TlfnknECC801S
Conrad Johnson PV-5 w/mods
TT Conrad Johnson Sonographe SG3 Oak / Sumiko LMT / Grado Woodbody Platinum / Sumiko PIB2 / The Clamp
Musical Fidelity A1 CDPro/ Bada DD-22 Tube CDP / Conrad Johnson SD-22 CDP
Tuners w/mods Kenwood KT5020 / Fisher KM60
MF x-DAC V8, HAInfo NG27
Herbies Ti-9 / Vibrapods / MIT Shotgun AC1 IEC's / MIT Shotgun 2 IC's / MIT Shotgun 2 Speaker Cables
PS Audio Cryo / PowerPort Premium Outlets / Exact Power EP15A Conditioner
Walnut SDA 2B TL /Oak SDA SRS II TL (Sonicaps/Mills/Cardas/Custom SDA ICs / Dynamat Extreme / Larry's Rings/ FSB-2 Spikes
NAD SS rigs w/mods
GIK panels -
inspiredsports wrote: »Yes they are a huge compromise, but with all due respect I would qualify that advice.
--- If you have clean audio sources and are reasonable about turning your volume down if you sense distortion, remove and "jumper" them.
--- If you crank it with reckless abandon and/or have low quality sources/amps/etc., replace them.
Excellent advice. I was hoping he already knew it... -
Excellent advice. I was hoping he already knew it...
I did from previous threads but after just spending $300 for new 198's and my luck I figured all the insurance I can get. Polk CS is awesome sent me 4 new ones and got them in two days! I will install when I really get bored.
