'old member', first post

Define 'old' and 'member' however you like... I am not afraid.

This might(if it works) be my first post on this site, I'm a Polk'ster since '92 when
I purchased(much to the dismay of my wife at the time-funny how a guy remembers such things...) my RTA 11TL's, which David(#Westmassguy) has just completed a crossover re-build(!) on. They were my daily drivers(nyuck..nyuck) from '92 until 2015 when we( the latest wife-meet the new boss, not quite the same as the old boss!) moved into our current home and took advantage of a Polk F/F sale(late 2014) and went with 'newer stuff' for the new living room.
But I soon missed the 2-channel sound of the 11TL's until this Spring it became a mission to see what they had left in them. Hopefully, I'll know in a couple more weeks.

I also seem to remember another Polk 'forum', back around '95-96 but I can't honestly recall if it was Polk-based, or just a Polk section of a general hi-fi forum.

Thanks much to everyone here, and no longer here, for the reading material
of the last several years and beyond. I hope to contribute every now and again.

As you were...

-glenn

Comments

  • audioluvraudioluvr Posts: 2,375
    Welcome. Those were some mighty fine looking crossovers Dave did for you! I have a pair of the RTA 11T's I refreshed at my GF's house. They are a great sounding speaker.
    One foot on audio nirvana and the other in the poor house.
  • F1nutF1nut Posts: 44,820
    Nice introduction, welcome to Club Polk.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • westmassguywestmassguy Posts: 6,671
    gramey wrote: »
    Define 'old' and 'member' however you like... I am not afraid.

    This might(if it works) be my first post on this site, I'm a Polk'ster since '92 when
    I purchased(much to the dismay of my wife at the time-funny how a guy remembers such things...) my RTA 11TL's, which David(#Westmassguy) has just completed a crossover re-build(!) on. They were my daily drivers(nyuck..nyuck) from '92 until 2015 when we( the latest wife-meet the new boss, not quite the same as the old boss!) moved into our current home and took advantage of a Polk F/F sale(late 2014) and went with 'newer stuff' for the new living room.
    But I soon missed the 2-channel sound of the 11TL's until this Spring it became a mission to see what they had left in them. Hopefully, I'll know in a couple more weeks.

    I also seem to remember another Polk 'forum', back around '95-96 but I can't honestly recall if it was Polk-based, or just a Polk section of a general hi-fi forum.

    Thanks much to everyone here, and no longer here, for the reading material
    of the last several years and beyond. I hope to contribute every now and again.

    As you were...

    -glenn

    I think you'll be pleased with the new Sonicaps Glenn.
    Home Theater/2 Channel:
    Front: SDA-2ATL forum.polkaudio.com/discussion/143984/my-2as-finally-finished-almost/p1
    Center: Custom Built forum.polkaudio.com/discussion/150760/my-center-channel-project/p1
    Surrounds & Rears: Custom Built forum.polkaudio.com/discussion/151647/my-surround-project/p1
    Sonicaps, Mills, RDO-194s-198s, Dynamat, Hurricane Nuts, Blackhole5
    Pioneer Elite VSX-72TXV, Carver PM-600, SVS PB2-Plus Subwoofer
    Cables: Speaker: Furez 10/2 with GLS Locking Banana Plugs
    Interconnect: Furez 10/2 with SpeakONs
    ICs: Custom Furez by Douglas Connections
    Den:
    Bose 901 Series II Continentals Restored, Re-Built Equalizer with Elna Silmic IIs, Sonicaps, and Silver Mica Caps
    Carver CT-3 Pre, Carver C-500

    dhsspeakerservice.com/
    Exclusive Distributor of Gimpod's Custom SDA Circuit Boards

    "And keep her under 70, would you, huh? Betty likes a slow ride"
Sign In or Register to comment.

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!