bi-wiring rtiA5
PixOtt
Posts: 15
anybody tried to bi-wire your rtia5? how does it perform after bi-wiring? I want to do bi-wire with my Yamaha RX-V2400, it has got speaker A B setup allowes to bi-wire. Any thoughts? Happy new year 
Comments
-
if you have the wire, try it. expect others to chime in w/"don't waste your time."Samsung 60" QN65Q7FAMFXZA QLED, Outlaw Audio 976 Pre/Pro, Samsung BDP, Amazon Firestick, Phillips CD Changer
Canare 14 ga - LCR tweeters inside*; Ctr Ch outside
BJC 10 ga - LCR mids “Foamed” & “Plugged**”, inside* & out
8 ga Powerline: LR woofers, inside* & out
*soldered **Rob the Man (Xschop)
LR: Tri-amped RTi A7 w/Rotels*. Woofers - 980BX; Tweets & Mids - RB981*
Ctr Ch: Rotel RB981* -> Bi-amped CSi A6
Surrounds: Rotel 981* -> AR 12 ga -> RTi A3
*all connected w/Premiere ICs
5 Subs: Sunfire True SW Signature -> LFE & Ctr Ch; 4 Audio Pro Evidence @ the “Corners”
Power Conditioning & Distribution:
4 dedicated 20A feeds; APC H15; 5 Furman Miniport 20s -
Simply replace the stock jumper plates with high quality speaker cable.Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."
President of Club Polk -
Simply replace the stock jumper plates with high quality speaker cable.
16 gauge and any recommended brands? thanks
-
If you are stuck on gauge, it's not high quality speaker cable. However, it would be better than the stock plates.Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."
President of Club Polk -
start w/whatever you have though I'd go heavier than that between the amp/AVR and speakers.
my $0.01
PS: welcome to Club Polk if you haven't receive that
TonySamsung 60" QN65Q7FAMFXZA QLED, Outlaw Audio 976 Pre/Pro, Samsung BDP, Amazon Firestick, Phillips CD Changer
Canare 14 ga - LCR tweeters inside*; Ctr Ch outside
BJC 10 ga - LCR mids “Foamed” & “Plugged**”, inside* & out
8 ga Powerline: LR woofers, inside* & out
*soldered **Rob the Man (Xschop)
LR: Tri-amped RTi A7 w/Rotels*. Woofers - 980BX; Tweets & Mids - RB981*
Ctr Ch: Rotel RB981* -> Bi-amped CSi A6
Surrounds: Rotel 981* -> AR 12 ga -> RTi A3
*all connected w/Premiere ICs
5 Subs: Sunfire True SW Signature -> LFE & Ctr Ch; 4 Audio Pro Evidence @ the “Corners”
Power Conditioning & Distribution:
4 dedicated 20A feeds; APC H15; 5 Furman Miniport 20s -
This is the "don't waset you time" that gp4 mentioned.Main Rig:
Krell KAV 250a biamped to mid/highs
Parasound HCA1500A biamped to lows
Nakamichi EC100 Active xover
MIT exp 1 ic's
Perreaux SA33 class A preamp
AQ kingcobra ic's
OPPO 83 CDP
Lehmann audio black cube SE phono pre, Audioquest phono wire (ITA1/1)
Denon DP-1200 TT. AToc9ML MC cart.
Monster HTS 3600 power conditioner
ADS L1590/2 Biamped
MIT exps2 speaker cable -
I use 14 gauge quad cable from blue jeans and am fine with it. Personally, I would spend my money on other things.....The biggest difference that I’ve noticed in my setup is the crossover mod on my RTi8’s. I used Sonicap caps and Mills resistors.
