Found The Pin Blade Connector Online

PolkieMan
PolkieMan Posts: 2,446
edited December 2012 in DIY, Mods & Tweaks
I think this is it. You guys please correct me if I am wrong.

http://www.mcmelectronics.com/product/DISTRIBUTED-BY-MCM-13HP035B-/CN00767
POLK SDA 2.3 TLS BOUGHT NEW IN 1990, Gimpod/Sonic Caps/Mills RDO-198
POLK CSI-A6 POLK MONITOR 70'S ONKYO TX NR-808 SONY CDP-333ES
PIONEER PL-510A SONY BDP S5100
POLK SDA 1C BOUGHT USED 2011,Gimpod/Sonic Caps/Mills RDO-194
ONKYO HT RC-360 SONY BDP S590 TECHNICS SL BD-1
Post edited by PolkieMan on
· Share on FacebookShare on Twitter

Comments

  • Conradicles
    Conradicles Posts: 6,092
    edited November 2012
    Not sure but it looks like one. You are aware the blade does nothing and all you need is the pin? A high quality RCA cable modified works great.
    · Share on FacebookShare on Twitter
  • PolkieMan
    PolkieMan Posts: 2,446
    edited November 2012
    Yes that is what I am using now but in would be nice to make one like the original and of course get the extra support. I just thought these were unavailable anywhere till today. Shipping is too much though.
    POLK SDA 2.3 TLS BOUGHT NEW IN 1990, Gimpod/Sonic Caps/Mills RDO-198
    POLK CSI-A6 POLK MONITOR 70'S ONKYO TX NR-808 SONY CDP-333ES
    PIONEER PL-510A SONY BDP S5100
    POLK SDA 1C BOUGHT USED 2011,Gimpod/Sonic Caps/Mills RDO-194
    ONKYO HT RC-360 SONY BDP S590 TECHNICS SL BD-1
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,303
    edited November 2012
    Keeping these speakers original is overrated anyways. When there are much better options with connectors and cables to be used..


    Get your modding on I say!!:lol:
    Polk Audio SDA 2.3tl Fully Hot Rodded. 😎

    SVS SB16 X2

    Cary SLP-05/Ultimate Upgrade.
    Cary SA-500.1 ES Amps
    Cary DMS 800PV Network
    OPPO UDP 205/ModWright Modification
    VPI Scout TT / Dynavector 20x2
    Jolida JD9 Fully Modified

    VPI MW-1 Cyclone RCM

    MIT Shotgun 3 cables throughout / Except TT, and PC’s
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited November 2012
    NL2 is where it is at!
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,649
    edited November 2012
    PolkieMan wrote: »
    I think this is it. You guys please correct me if I am wrong.

    http://www.mcmelectronics.com/product/DISTRIBUTED-BY-MCM-13HP035B-/CN00767

    That's a DIN connector, it will not work on SDA's.

    The company that made the originals was bought out years ago and that company does not make the pin/blade connectors.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • PolkieMan
    PolkieMan Posts: 2,446
    edited December 2012
    Thanks for the reply!
    I will probably go the binding post route since the original is gone forever.
    F1nut wrote: »
    That's a DIN connector, it will not work on SDA's.

    The company that made the originals was bought out years ago and that company does not make the pin/blade connectors.
    POLK SDA 2.3 TLS BOUGHT NEW IN 1990, Gimpod/Sonic Caps/Mills RDO-198
    POLK CSI-A6 POLK MONITOR 70'S ONKYO TX NR-808 SONY CDP-333ES
    PIONEER PL-510A SONY BDP S5100
    POLK SDA 1C BOUGHT USED 2011,Gimpod/Sonic Caps/Mills RDO-194
    ONKYO HT RC-360 SONY BDP S590 TECHNICS SL BD-1
    · Share on FacebookShare on Twitter
  • Systems
    Systems Posts: 14,873
    edited December 2012
    Cinch still makes the right pin/blade connector.
    They also make the right blade/blade.

    That said, you are WAY better off going binding posts.
    Just being able to use any speaker cable you like would pay off enough for
    the investment.

    Most all of the Pin and Blade connectors are nickle plated anyway.
    WOULD not be beneficial for SQ in the least.
    Testing
    Testing
    Testing
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,649
    edited December 2012
    Cinch still makes the right pin/blade connector.

    Got a link for that?
    That said, you are WAY better off going binding posts.

    Gotta disagree, Neutrik is the way to go.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter