Round 2 for

Toolfan66
Toolfan66 Posts: 17,982
edited July 2010 in DIY, Mods & Tweaks
Driver and passive rings coming soon!!!

This is just an FYI I will start a new thread soon. So no need to place an order here.. Those of you that have PM'ed me I will be in touch just so you know I'm not ignoring you...

All the little problems we had since I do not own every Polk speaker has been taken care of the next run should be more of a drill drop in job..

Thanks,

Larry.
Post edited by Toolfan66 on
· Share on FacebookShare on Twitter

Comments

  • F1nut
    F1nut Posts: 51,674
    edited July 2010
    Most excellent!!!
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • Vette C6.r
    Vette C6.r Posts: 1,560
    edited July 2010
    I am interested Larry. I sent you a PM.

    Tweeter rings included on the next round ??
    · Share on FacebookShare on Twitter
  • nooshinjohn
    nooshinjohn Posts: 25,877
    edited July 2010
    You are a blessing to CP Larry. Keep up the fantastic work.
    The Gear... Carver "Statement" Mono-blocks, Mcintosh C2800 Arcam AVR20, Oppo UDP-203 4K Blu-ray player, Sony XBR70x850B 4k, Polk Audio Legend L800 with height modules, L400 Center Channel Polk audio AB800 "in-wall" surrounds. Marantz MM7025 stereo amp. Simaudio Moon 680d DSD

    “When once a Republic is corrupted, there is no possibility of remedying any of the growing evils but by removing the corruption and restoring its lost principles; every other correction is either useless or a new evil.”— Thomas Jefferson

    How many flies need to be buzzing a dead horse before you guys stop beating it?
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,982
    edited July 2010
    Well I only wish I had half the Knowledge of some of the guys here. It's what I get for getting into the game late... LOL
    · Share on FacebookShare on Twitter
  • Hawkeye
    Hawkeye Posts: 1,313
    edited July 2010
    Vette C6.r wrote: »
    I am interested Larry. I sent you a PM.

    Tweeter rings included on the next round ??

    Wouldn't that be tweeter rectangles?:D Put me down for four of those!

    Gordon
    2 Channel -
    Martin Logan Spire, 2 JL Audio F112 subs
    McIntosh C1000 Controller with Tube pre amp, 2 MC501 amplifiers, MD1K Transport & DAC, MR-88 Tuner
    WireWorld Eclipse 6.0 speaker wire and jumpers, Eclipse 5^2 Squared Balanced IC's. Silver Eclipse PCs (5)
    Symposium Rollerblocks 2+ (16)Black Diamond Racing Mk 3 pits (8)
    · Share on FacebookShare on Twitter
  • helipilotdoug
    helipilotdoug Posts: 1,230
    edited July 2010
    If you are going to do tweeter retainers, put me down for 6.
    Sunfire Theater Grand IV
    Sunfire Cinema Grand Signature
    SRS 2.1TL
    SDA 2BTL's
    CSiA6
    FXiA4
    FXiA6
    SDA 2A's
    Monitor 10A's
    http://www.douglasconnection.com
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,982
    edited July 2010
    No tweeters just yet.. I still have to do some progaming for the template, and I just have not had the time...


    It will be Soon. The nice thing is you will be able to use these on the Crossover plates for the SRS,1.2/1.2tl as well. Hell if you wanted you could use them on the binding post cups too..

    Larry..
    · Share on FacebookShare on Twitter
  • Vette C6.r
    Vette C6.r Posts: 1,560
    edited July 2010
    I am interested in round 2 Larry.
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,982
    edited July 2010
    Check the FM;)
    · Share on FacebookShare on Twitter
  • audiobilly
    audiobilly Posts: 351
    edited July 2010
    Larry, will there be a round 3? I would like some for the Monitor 10s' that I have, but need to hold off on spending the funds right now. If this is the last round then I need to sell my body!

    I have a friend that has Monitor 12s'. Is the PR the same as the 3.1s'? If so this means that the 6.5" rings and the 3.1 PR ring should work for the Monitor 12s'. What cha think?

    Thank you Larry!!!!!!!!!

    P.S. Do you remember us talking about a template set? We talked via PM once upon a time.
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,982
    edited July 2010
    audiobilly wrote: »
    Larry, will there be a round 3? I would like some for the Monitor 10s' that I have, but need to hold off on spending the funds right now. If this is the last round then I need to sell my body!

    I have a friend that has Monitor 12s'. Is the PR the same as the 3.1s'? If so this means that the 6.5" rings and the 3.1 PR ring should work for the Monitor 12s'. What cha think?

    Thank you Larry!!!!!!!!!

    P.S. Do you remember us talking about a template set? We talked via PM once upon a time.


    I cannot promise a round 3..
    · Share on FacebookShare on Twitter
  • hoosier21
    hoosier21 Posts: 4,415
    edited July 2010
    TOOLFORLIFEFAN wrote: »
    Check the FM;)

    checked and nothing there, ;)

    line is forming
    Dodd - Battery Preamp
    Monarchy Audio SE100 Delux - mono power amps
    Sony DVP-NS999ES - SACD player
    ADS 1230 - Polk SDA 2B
    DIY Stereo Subwoofer towers w/(4) 12 drivers each
    Crown K1 - Subwoofer amp
    Outlaw ICBM - crossover
    Beringher BFD - sub eq

    Where is the remote? Where is the $%#$% remote!

    "I've always been mad, I know I've been mad, like the most of us have...very hard to explain why you're mad, even if you're not mad..."
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,982
    edited July 2010
    Here ya go;)



    http://www.polkaudio.com/forums/showthread.php?t=104460



    .
    · Share on FacebookShare on Twitter