SDA Non-Common Ground Amp Interface

bluecomet
bluecomet Posts: 1,118
edited March 2010 in For Sale (FS) Classifieds
Here's the deal with this cable. I got it when I bought my second pair of SRS 1.2tl's. The original owner bought and decided he did not want to use a non common ground amp so he cut off the box and connected the pin/blade cable. So this cable would need to be soldered to the box which is a simple thing to do and you will have an original non common ground amp interface to use with high powered mono block amps. I know this cables go for high sums of money on ebay but I am offering it here first to the club at what I believe is a fair price. The price is two hundred dollars plus fifteen dollars shipped anywhere in the CONUS. Money orders only accepted on this. Thanks.
Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
Yamaha RX-V2500 System, Carver A753 3 channel amp.

Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
Post edited by bluecomet on
· Share on FacebookShare on Twitter

Comments

  • bluecomet
    bluecomet Posts: 1,118
    edited March 2010
    Bump before it goes on ebay.
    Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
    Yamaha RX-V2500 System, Carver A753 3 channel amp.

    Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

    Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
    · Share on FacebookShare on Twitter
  • george daniel
    george daniel Posts: 12,096
    edited March 2010
    Well,, good luck on e-bay--you know that you can build one (dreadnaught) for about the same price,,I'd like to have an original,,but I guess I'll just build another--good luck with your sale.
    JC approves....he told me so. (F-1 nut)
    · Share on FacebookShare on Twitter
  • TroyD
    TroyD Posts: 13,098
    edited March 2010
    Seems pretty steep for a hatchet job...
    I plan for the future. - F1Nut
    · Share on FacebookShare on Twitter
  • bluecomet
    bluecomet Posts: 1,118
    edited March 2010
    It's on ebay for $125.00 Cut the wires where the originalblack jacket is then solder the wires. It would look as good as new but be about 6 inches shorter than normal. I could of done this and no one would be the wiser but I was straight up about the cable. It's not a big project. This original cable went for hundreds a couple of months back on ebay. The cable is worth what someone is willing to pay to keep there speaker set original. It's just like some guys want SL2000 original tweets. I prefer RDO 194's. To each his own.
    Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
    Yamaha RX-V2500 System, Carver A753 3 channel amp.

    Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

    Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
    · Share on FacebookShare on Twitter