FS: POLK PA 500.4 & 1200.1 amps - BNIB

Thunderplains
Thunderplains Posts: 38
edited December 2009 in Garage Sale
FOR SALE:

Brand new, never used.

Polk PA500.4 Amp
Polk PA1200.1 Amp

I am shedding half my amp install as I am changing my setup a little.
You pay what I paid, not looking to make $$..

SPECS:

500.4 -
* 125 watts x 4 continuous, 200 x 4 dynamic power (2 ohm load), 4 channel mode.
* 250 watts x 2 (4 ohm) continuous power, 2 channel mode.
* CEA-2006 Compliant specifications for true, accurate power ratings.
* 4-channel, dual bridge-mono (2-channel), or dual simultaneous stereo/mono operation provide a variety of configurations and setups: 4-channel for front and rear speakers; 2 speakers and a sub; 2 subwoofers; or 2 subs and 4-channels in passive-tri mode.
* 2 ohm stable 4-channel operation.
* High-speed MOSFET switching power supply and high current Bipolar Output Transistors pump maximum voltage and high current to your speakers or subwoofers.
* Double Layer Fiberglass Epoxy Printed Circuit Boards for more rigidity, less shrinkage and a smaller overall amp footprint.
* 6-Way Smart System Protection (SSP) circuits
* Fully adjustable (50- 500Hz) 12 dB/octave high- or low-pass crossover. Defeatable for full range (flat) operation.
* Switchable 8 dB bass boost at 40Hz for extra bass thump.
* Variable input gain optimizes match with different signal sources (250mv to 7.5V).
* RCA Outputs (front channels only) for easy daisy chaining of other amplifiers.
* Mounting hardware with rubber isolation grommets and extra fuses included.
* Light Bar/Fan Output- Connect an optional LED light bar or cooling fan for custom installations.
* Multi-Color Status LED gives instant information on amplifier operation.
* Remote Subwoofer Level Adjuster for rear channels included.

1200.1 -
* Monoblock amplifier for subwoofer use and particularly ideal for the SR Series.
* 1200 watts x 1 (1 ohm), 800 watts x 1 (2 ohm) and 400 watts x 1 (4 ohm) continuous power. CEA-2006 Compliant specifications for true, accurate power ratings.
* 2400 watts x 1 (1 ohm) dynamic power.
* 1 ohm stable design can drive even the most demanding subwoofers.
* Super Efficient Class D Pulse Width Modulation amplifier design. Draws less power and runs cooler so you won't heat up the inside of your vehicle or make the headlights dim.
* High-speed MOSFET switching power supply and high current Bipolar Output Transistors pump maximum voltage and high current to your speakers or subwoofers.
* Double Layer Fiberglass Epoxy Printed Circuit Boards for more rigidity, less shrinkage and a smaller overall amp footprint.
* 6-Way Smart System Protection (SSP) circuits
* Anodized extruded brushed-aluminum cover for maximum heat dissipation and great looks!
* Cast aluminum textured end caps for optimized heat dissipation and hiding of connectors. Solid aluminum logo and model panel back lit in cobalt blue.
* Adjustable 12 dB/octave low-pass crossover (30-250 Hz).
* Switchable 8 dB bass boost at 40Hz for extra bass thump.
* Variable input gain optimizes match with different signal sources (250mv to 7.5V).
* Switchable 24 dB/octave subsonic filter protects ported subwoofers.
* Switchable 180° phase inversion for easy sub to main integration or external bridge mono operation.
* Mounting hardware with rubber isolation grommets and extra fuses included.
* Light Bar/Fan Output- Connect an optional LED light bar or cooling fan for custom installations.
* Multi-Color Status LED gives instant information on amplifier operation.
* Remote Subwoofer Level Adjuster included.
* Master/Slave switch and RCA Outputs for easy daisy chaining of other amplifiers.
* Master/Slave switch allows parallel operation- master amp's gain and crossover settings will be duplicated in "slave" amplifiers for consistent, repeatable settings.
* Power and ground terminals accept bare wire up to 4 AWG. Terminals use standard #2 Phillips head screwdriver- no more hex wrenches to lose or strip!


$575 shipped for both

If you want to pay by paypal, add 3%.. Thx
Post edited by Thunderplains on

Comments