WTB- SDA Grill Logos

Herfnwolf
Herfnwolf Posts: 52
edited October 2008 in Wanted (WTB) Classifieds
I bought a pair of SDA SRS 3.1TL that were missing the logos (M. Polk Signature) that are on the upper part of the cloth grill.

If anyone knows where I can get a pair, please let me know.

Many thanks,
DJ
Raleigh,NC:o
original Monitor 10Bs
Original Rosewood LS90s,
SDA 3.1TL,
LS/FX
CS350
NHT 2 x SW3P/SA-3
B&K Ref 30,ST125.2,AV5000
[/FONT]
Post edited by Herfnwolf on

Comments

  • Herfnwolf
    Herfnwolf Posts: 52
    edited September 2008
    Thanks Lazareath,
    Good luck with the wedding and all. I need to find the larger square originals if at all possible to cover the residual adhesive left on the cloth grill. If i had a very good copy , PDF,or scan that is to scale I would have a couple made at a friends shop.

    If I don't get any leads I may come begging for a scan...:o;)

    Thanks again for the input.

    DJ
    Raleigh,NC
    original Monitor 10Bs
    Original Rosewood LS90s,
    SDA 3.1TL,
    LS/FX
    CS350
    NHT 2 x SW3P/SA-3
    B&K Ref 30,ST125.2,AV5000
    [/FONT]
  • Herfnwolf
    Herfnwolf Posts: 52
    edited September 2008
    Well, realistically I don't think it would be an exact replica but maybe something programmed and engraved could be possible. I will not know exactly what he can do until I stick something under his nose. It may be too cost prohibitive but I'm determined to do something and get these 3.1TLs looking back to original and spiffed up a bit. Maybe something will turn up before I go to the duplicating route.

    DJ
    original Monitor 10Bs
    Original Rosewood LS90s,
    SDA 3.1TL,
    LS/FX
    CS350
    NHT 2 x SW3P/SA-3
    B&K Ref 30,ST125.2,AV5000
    [/FONT]
  • zingo
    zingo Posts: 11,258
    edited September 2008
    Keep your eye on ebay as there is always logo popping up. Usually they are just the small ones, but you never know with ebay...
  • Herfnwolf
    Herfnwolf Posts: 52
    edited October 2008
    I'm still looking for any SDA grills with logos or just logos to put on my 3.1TLs. They sound great but look like they are missing a tooth with out the Polk SDA logos.

    Please let me know of any source for these logos. Thanks

    DJ
    Raleigh,NC
    original Monitor 10Bs
    Original Rosewood LS90s,
    SDA 3.1TL,
    LS/FX
    CS350
    NHT 2 x SW3P/SA-3
    B&K Ref 30,ST125.2,AV5000
    [/FONT]
  • F1nut
    F1nut Posts: 50,569
    edited October 2008
    eBay
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • Herfnwolf
    Herfnwolf Posts: 52
    edited October 2008
    Thanks F1 for the obvious suggestion.

    I continue to send requests to all ebay gear sellers, searching for leads everywhere (here included). etc. Maybe someone will remember where an old pair of scrap SDAs,grills or logos are laying around or just decide to sell a few they have collected. ;^)


    DJ
    Raleigh,NC
    original Monitor 10Bs
    Original Rosewood LS90s,
    SDA 3.1TL,
    LS/FX
    CS350
    NHT 2 x SW3P/SA-3
    B&K Ref 30,ST125.2,AV5000
    [/FONT]
  • F1nut
    F1nut Posts: 50,569
    edited October 2008
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • Herfnwolf
    Herfnwolf Posts: 52
    edited October 2008
    F1,
    Again, thanks for an obvious but incorrect suggestion of Polk SDA logos on ebay at the current time. Thanks for trying to help though. I'll keep looking.

    DJ
    Raleigh,NC
    original Monitor 10Bs
    Original Rosewood LS90s,
    SDA 3.1TL,
    LS/FX
    CS350
    NHT 2 x SW3P/SA-3
    B&K Ref 30,ST125.2,AV5000
    [/FONT]
  • gdb
    gdb Posts: 6,012
    edited October 2008
    This is just a suggestion, and it's possible that I am wrong,but....I think what you are asking for are emblems/badges that were only applied to the SRS series of SDAs. I bought two pairs of non-SRS SDAs that had only the small
    polkaudio emblems on the grilles. My new SRS2s have the rectangular ones at the upper corners of the grilles. If you re-word your WTB post to specify the SRS type emblem, you might have better luck in your hunt !:)Geoff
  • F1nut
    F1nut Posts: 50,569
    edited October 2008
    Unbelieveable.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk

  • NJPOLKER
    NJPOLKER Posts: 3,474
    edited October 2008
    LMAO
    Talking to the Club Polk president like that,wow. Maybe you should stop being soooo nice.
  • F1nut
    F1nut Posts: 50,569
    edited October 2008
    DJ sent me a nice PM and we have worked things out. I simply thought that the generic Polk Audio emblem may work for him until/if he could find the SRS emblem. He understands that now. All good, let's move on.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."


    President of Club Polk