SDA-2B Xover problem found

fbm211
fbm211 Posts: 1,488
edited May 2008 in Vintage Speakers
I removed the right channel crossover to pack for shipping and noticed that one of those black things with red wire wrapped around it and is strapped to the board is loose.I think it used to be glued down.Anyway there is a lead on both ends that have broken away from the board.I would guess this goes to the stereo driver.
SDA-2BTL with custom IC
Adcom 565 monoblocks--Monarchy Audio M-10 preamp
Theta Data Basic Transport--Stello DA100 Signature DAC--Camelot Dragon Pro2 MK III
Harman Kardon T-55c TT
DH Labs Q-10 Signature Speaker Cables With Furez silver plated copper bananas
Revelation Audio Labs Prophecy Cryo-Silver Reference AES/EBU
Revelation Audio Labs Prophecy Cryo-Silver i2s digital cable
4 Furutech FP-314Ag with FI-11cu Plugs/FI-11AG IECs--- Power Cords
DH LABS REVELATIONS ICs-amps
Revelation Audio Labs Paradise cryo-silver ICs-Source to pre
Post edited by fbm211 on
· Share on FacebookShare on Twitter

Comments

  • F1nut
    F1nut Posts: 50,734
    edited May 2008
    That's one of the inductors. Resolder it to the board and you'll be good to go.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • fbm211
    fbm211 Posts: 1,488
    edited May 2008
    I dont have a soldering kit and there isnt enough wire to spare to do so.What wire there is seems to have that red coating on it and there isnt enough to reach.
    SDA-2BTL with custom IC
    Adcom 565 monoblocks--Monarchy Audio M-10 preamp
    Theta Data Basic Transport--Stello DA100 Signature DAC--Camelot Dragon Pro2 MK III
    Harman Kardon T-55c TT
    DH Labs Q-10 Signature Speaker Cables With Furez silver plated copper bananas
    Revelation Audio Labs Prophecy Cryo-Silver Reference AES/EBU
    Revelation Audio Labs Prophecy Cryo-Silver i2s digital cable
    4 Furutech FP-314Ag with FI-11cu Plugs/FI-11AG IECs--- Power Cords
    DH LABS REVELATIONS ICs-amps
    Revelation Audio Labs Paradise cryo-silver ICs-Source to pre
    · Share on FacebookShare on Twitter
  • dcmeigs
    dcmeigs Posts: 708
    edited May 2008
    Use 600 grit sandpaper on that coating and you will be down to copper. Any hardware store will have a 3.99 soldering iron. Make it happen!
    The world is full of answers, some are right and some are wrong. - Neil Young
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,734
    edited May 2008
    Go to Radio Shack, buy a soldering gun, solder and some 20 gauge wire. Strip the insulation off a length of wire and make 2 pieces. Then, make a half loop at one end of each piece. Next, scrape or sand the red coating off a short section of each wire coming off the inductor and make a half loop at the end. Join the loop end of the inductor wire with the loop end of the new wire, pinch together and solder the joint. Place the inductor on the board, solder the new leads in the proper holes and use hot glue to secure the inductor to the board. Reassemble and enjoy your speakers.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter