Non-common ground interface

BigJim
BigJim Posts: 48
edited August 2006 in For Sale (FS) Classifieds
$100 shipped, what I paid for it from a fellow member. I've had my fun, now try out those huge monoblocks......
sda.jpg 120.8K
Post edited by BigJim on
· Share on FacebookShare on Twitter

Comments

  • BlueMDPicker
    BlueMDPicker Posts: 7,569
    edited August 2006
    Sold! I'll PM you for payment details.
    · Share on FacebookShare on Twitter
  • univera
    univera Posts: 848
    edited August 2006
    BMP, if you change your mind or want some extra money, I'd be happy to take it myself. Would love to run the hybrids in mono and get some serious power to the SRS's. I assume these interfaces are hard to find. Can these be homemade?

    Edit. Nevermind, enjoy!
    UNIVERA
    Historic Charleston SC

    2 Channel:
    SDA-SRS's RDO tweets
    Biamped Anthem 2 SE's w/1970's NOS Siemens CCA's
    Anthem Pre 2L w/E.harmonix platinum matched 6H23's
    CDP- NAD C 542


    HT setup:
    AVR: NAD T 773
    Rears: Polk LC80i
    DVD: Toshiba 3109 dual tray
    Subs: Velodyne and M&K
    T.V.: Sony KDL-52XBR4 w/Vans Evers Clean Line Jr.
    Conditioner: Panamax M5100EX

    Master Bedroom Sony 40KDL-XBR3

    "I love it when a plan comes together." Hannibal Smith, The A-Team
    · Share on FacebookShare on Twitter
  • Emlyn
    Emlyn Posts: 4,489
    edited August 2006
    The interface doesn't work with the SDA-SRS, unless it's the 1.2 or 1.2TL.

    As 4 ohm nominal speakers, you're better off biamping the SDA-SRS with the Anthem amps instead of bridging them anyway.
    · Share on FacebookShare on Twitter
  • univera
    univera Posts: 848
    edited August 2006
    Thanks. You answered a question I hadn't yet asked. Didn't know if they worked with the SRS's. Plus, I didn't need anything else to further complicate my confused mind:)
    UNIVERA
    Historic Charleston SC

    2 Channel:
    SDA-SRS's RDO tweets
    Biamped Anthem 2 SE's w/1970's NOS Siemens CCA's
    Anthem Pre 2L w/E.harmonix platinum matched 6H23's
    CDP- NAD C 542


    HT setup:
    AVR: NAD T 773
    Rears: Polk LC80i
    DVD: Toshiba 3109 dual tray
    Subs: Velodyne and M&K
    T.V.: Sony KDL-52XBR4 w/Vans Evers Clean Line Jr.
    Conditioner: Panamax M5100EX

    Master Bedroom Sony 40KDL-XBR3

    "I love it when a plan comes together." Hannibal Smith, The A-Team
    · Share on FacebookShare on Twitter
  • BlueMDPicker
    BlueMDPicker Posts: 7,569
    edited August 2006
    Emlyn wrote:
    The interface doesn't work with the SDA-SRS, unless it's the 1.2 or 1.2TL.
    ...or, SRS with certain serial numbers (which I don't have). This will work, however, with my 2Bs and a dual mono digital amp.

    It will stay in the club if I no longer need it.
    · Share on FacebookShare on Twitter
  • amulford
    amulford Posts: 5,020
    edited August 2006
    Dibs
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,554
    edited August 2006
    ...or, SRS with certain serial numbers (which I don't have).

    I always forget about this. It will work with the SRS if they both have serial numbers above 5001.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • BigJim
    BigJim Posts: 48
    edited August 2006
    I believe Ken @ Polk said that it will work with any pin/blade SDA's???
    · Share on FacebookShare on Twitter
  • reeltrouble1
    reeltrouble1 Posts: 9,312
    edited August 2006
    I was going to say yes, then remembered something about the SDA 1c's and certain serial numbers and not being able to use it.

    RT1
    · Share on FacebookShare on Twitter