POwer cord Denon 2807/ Yamaha 2500 help

mariolondono
mariolondono Posts: 12
edited July 2006 in Electronics
This might be dumb but I have a question that’s been eating my mind and I need someones advice. I currently exchanged a Yamaha rxv 2500 for the new Denon 2807. The problem is that that I got stuck with the power cord for the yamaha 2500 and sent the new Denons power cord with the yamaha. I have hooked it up and it sound great but I am afraid that down the line this might have problems. I mean if you look at a normal receiver’s power cord you will see that they are almost generic. Any advice on this Matter? TAKE into consideration that the Yamaha was 130 watts and the Denon is 110 watts. Did I end up having a stronger Power cord for the Denon since the wattage is less? Please help and I need your advice.

Best Regards:

Mario
Post edited by mariolondono on
· Share on FacebookShare on Twitter

Comments

  • Toxis
    Toxis Posts: 5,116
    edited July 2006
    I'd say you're reading into it to much. ;) Just enjoy the sound. If you really want, just buy a better power cord from say Signal Cable and enjoy having even more power/dynamics.
    Never kick a fresh **** on a hot day.

    Home Setup: Sony VPL-VW85 Projo, 92" Stewart Firehawk, Pioneer Elite SC-65, PS3, RTi12 fronts, CSi5, FXi6 rears, RTi6 surround backs, RTi4 height, MFW-15 Subwoofer.

    Car Setup: OEM Radio, RF 360.2v2, Polk SR6500 quad amped off 4 Xtant 1.1 100w mono amps, Xtant 6.1 to run an eD 13av.2, all Stinger wiring and Raammat deadener.
    · Share on FacebookShare on Twitter
  • mariolondono
    mariolondono Posts: 12
    edited July 2006
    Hey tox:

    Thanxs for the message, just what I needed. I will check the cables you mentioned.

    Take care and thanx again for the reply
    · Share on FacebookShare on Twitter
  • Toxis
    Toxis Posts: 5,116
    edited July 2006
    anytime and welcome!!!
    Never kick a fresh **** on a hot day.

    Home Setup: Sony VPL-VW85 Projo, 92" Stewart Firehawk, Pioneer Elite SC-65, PS3, RTi12 fronts, CSi5, FXi6 rears, RTi6 surround backs, RTi4 height, MFW-15 Subwoofer.

    Car Setup: OEM Radio, RF 360.2v2, Polk SR6500 quad amped off 4 Xtant 1.1 100w mono amps, Xtant 6.1 to run an eD 13av.2, all Stinger wiring and Raammat deadener.
    · Share on FacebookShare on Twitter
  • janmike
    janmike Posts: 6,146
    edited July 2006
    I used to own a Yamaha RX-V1500, purchased a pwr cord from Signal and noticed a difference.
    Michael ;)
    In the beginning, all knowledge was new!
    NORTH of 60°
    · Share on FacebookShare on Twitter
  • mariolondono
    mariolondono Posts: 12
    edited July 2006
    I see that Signal cable has 3 types. Any sugestions?

    Thanx again guys!!
    · Share on FacebookShare on Twitter
  • janmike
    janmike Posts: 6,146
    edited July 2006
    I purchased the MagicPower Video Reference and actually should upgrade as I have a new processor. You can always ping Frank at Signal and get his advice.
    Michael ;)
    In the beginning, all knowledge was new!
    NORTH of 60°
    · Share on FacebookShare on Twitter
  • steveinaz
    steveinaz Posts: 19,538
    edited July 2006
    E-Mail sent mariolondono....
    Source: Bluesound Node 2i - Preamp/DAC: Benchmark DAC2 DX - Amp: Parasound Halo A21 - Speakers: MartinLogan Motion 60XTi - Shop Rig: Yamaha A-S501 Integrated - Shop Spkrs: Elac Debut 2.0 B5.2
    · Share on FacebookShare on Twitter
  • Grimster74
    Grimster74 Posts: 2,576
    edited July 2006
    Frank recommended I get the "MagicPower Digital Reference" power cord for my Denon 3805, which will soon be powering my Outlaw 990 Pre/Pro.
    Money Talks, Mine says Goodbye Rob!!!!
    · Share on FacebookShare on Twitter