WTB: Mid-Bass Driver Monitor 5b

MrBuhl
MrBuhl Posts: 2,419
edited December 2005 in Wanted (WTB) Classifieds
Greeting Polksters!

Upon further review - it appears that I have a burned MB driver in my new 5b's on one side (I already swapped drivers so I know it's the driver not the crossover). So I have a couple questions hopefully someone can help me with...

1. Do I need to replace them as a set or can I just do one?
2. Anyone have a spare one they want to part with?
3. I don't see replacement drivers on the Polk Site specifically for this driver, do I just call and give them my speaker part number for replacement? I understand it should run about $48?

Thanks for any/all assistance - hope everyone had a great holiday! (I recieved a Csi3 Center as top gift!!) :D

Ed
VA HT HK AVR20II, Sony S9000ES CD/DVD/SACD, Polk Audio RC80i / Polk Audio CSi3, 60" Panasonic Plasma, Nordost / Signal Cable A2 / Wireworld / Pangea / Magic Power
VA 2 Channel Focal Electra 926 speakers, Pass Labs X150.5 Amp, Eastern Electric MiniMax Preamp (Tutay mods), Eastern Electric Minimax CDP (Scott Nixon mods), Music Hall mmf 5.1 Turntable, Parks Audio Budgie Phono Pre , Audioengine B1 streamer, MIT S3 IC's / MIT Shotgun S3 Speaker Cables / PS Audio power cables
Noggin Schiit Valhalla, Pangea, Phillips Fidelio X1, Polk UF8000

Polk SDA1c modded
Polk CRS+ 4.1TL modded (need veneer)
Polk SDA2BTL (fully modded)
A/L 1000VA Dreadnought Canare 4s11 SDA cable
SACD Marantz DV8300
Sony S9000ES CD/DVD/SACD
Yamaha YP-D6
Soundcraftsmen PCR800
Audible Illusions L1 Preamp
Vincent MFA based Cocci Tube Preamp
Pho-700 Phono Pre
Signal Cable Silver Resolution IC's






Post edited by MrBuhl on
· Share on FacebookShare on Twitter

Comments

  • janmike
    janmike Posts: 6,146
    edited December 2005
    Many people have called Polk directly and they tell you what you need, how much and send it to you. I have dealt with Polk in Canada and they are great people. I would give them a call.
    Michael ;)
    In the beginning, all knowledge was new!
    NORTH of 60°
    · Share on FacebookShare on Twitter
  • MrBuhl
    MrBuhl Posts: 2,419
    edited December 2005
    Thanks Michael - that's what I figured but I thought I would float the idea of a used one as well...

    Also - is it OK to just replace the one or should they be both done at the same time?
    VA HT HK AVR20II, Sony S9000ES CD/DVD/SACD, Polk Audio RC80i / Polk Audio CSi3, 60" Panasonic Plasma, Nordost / Signal Cable A2 / Wireworld / Pangea / Magic Power
    VA 2 Channel Focal Electra 926 speakers, Pass Labs X150.5 Amp, Eastern Electric MiniMax Preamp (Tutay mods), Eastern Electric Minimax CDP (Scott Nixon mods), Music Hall mmf 5.1 Turntable, Parks Audio Budgie Phono Pre , Audioengine B1 streamer, MIT S3 IC's / MIT Shotgun S3 Speaker Cables / PS Audio power cables
    Noggin Schiit Valhalla, Pangea, Phillips Fidelio X1, Polk UF8000

    Polk SDA1c modded
    Polk CRS+ 4.1TL modded (need veneer)
    Polk SDA2BTL (fully modded)
    A/L 1000VA Dreadnought Canare 4s11 SDA cable
    SACD Marantz DV8300
    Sony S9000ES CD/DVD/SACD
    Yamaha YP-D6
    Soundcraftsmen PCR800
    Audible Illusions L1 Preamp
    Vincent MFA based Cocci Tube Preamp
    Pho-700 Phono Pre
    Signal Cable Silver Resolution IC's






    · Share on FacebookShare on Twitter
  • burdette
    burdette Posts: 1,194
    edited December 2005
    What is the specific model number of the driver you need?

    I may have one. I probably do NOT, but I may, and I'll check.

    Send me an email rather than reply here. I'm more likely to catch that and check for you.
    · Share on FacebookShare on Twitter