How to: Pin/Blade SDA 1C running off Adcom GFA-565 monos

2»

Comments

  • ratpin
    ratpin Posts: 85
    I think I figured it out. Just needed to know what colors connected to speaker and which ones ground.
    Polk: / SDA-CRS / SDA-1C / M-10B / M-7B / M-5 / M-5jr / RTA-11T / LSIM703 / LSIM704 / LSIM706 / RTI8 / CSI3 / CSI5 / RTI4 / RTI-A5 / CSI-A6 / RC80i / RC85i / RC6s / PSW300 / Atrium6 / Atrium4 / About a dozen pair of Atrium45 lol.
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,412
    ratpin wrote: »
    I think I figured it out. Just needed to know what colors connected to speaker and which ones ground.
    It dosn't matter as long as you do not mix the primary and secondary windings with each other.
    · Share on FacebookShare on Twitter
  • ratpin
    ratpin Posts: 85
    I had ordered a steel box before thinking of RFI being an issue. The box arrived today and I like the size and design better than the prefab aluminum one I’ve seen used. Do any test results show a measurable difference going from steel to aluminum? I have a nice roll of decent gauge copper sheeting I can line the box with.kczmkzgtts8l.jpeg
    lsc7ikpvnpyr.jpeg
    v7vdjn4mrrim.jpeg
    Polk: / SDA-CRS / SDA-1C / M-10B / M-7B / M-5 / M-5jr / RTA-11T / LSIM703 / LSIM704 / LSIM706 / RTI8 / CSI3 / CSI5 / RTI4 / RTI-A5 / CSI-A6 / RC80i / RC85i / RC6s / PSW300 / Atrium6 / Atrium4 / About a dozen pair of Atrium45 lol.
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,221
    That is a good looking box, measurable differences or not, I would at the very least line it with dynamat.

    Enjoy the project..
    · Share on FacebookShare on Twitter
  • ratpin
    ratpin Posts: 85
    74qwwqhm7bzu.jpeg
    9i3azokwjjdv.jpeg
    jj443stlz8rb.jpeg
    lzl0ab3y4r4h.jpeg
    jqzddry44vo5.jpeg
    Polk: / SDA-CRS / SDA-1C / M-10B / M-7B / M-5 / M-5jr / RTA-11T / LSIM703 / LSIM704 / LSIM706 / RTI8 / CSI3 / CSI5 / RTI4 / RTI-A5 / CSI-A6 / RC80i / RC85i / RC6s / PSW300 / Atrium6 / Atrium4 / About a dozen pair of Atrium45 lol.
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,412
    Coming along nicely!
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,495
    I like the Polk badge.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,412
    That came out very nice!
    · Share on FacebookShare on Twitter
  • ratpin
    ratpin Posts: 85
    Thanks. It was a fun little project. I may do another one for a different set of SDA’s
    Polk: / SDA-CRS / SDA-1C / M-10B / M-7B / M-5 / M-5jr / RTA-11T / LSIM703 / LSIM704 / LSIM706 / RTI8 / CSI3 / CSI5 / RTI4 / RTI-A5 / CSI-A6 / RC80i / RC85i / RC6s / PSW300 / Atrium6 / Atrium4 / About a dozen pair of Atrium45 lol.
    · Share on FacebookShare on Twitter