RT800I crossover

Topher0384
Topher0384 Posts: 3
in Wanted (WTB) Classifieds
I bought these towers about 8 months ago and just got around to hooking them up. Notice no working tweeter on one tower. Found a bad cross over. Does anyone know where I can source one at?
· Share on FacebookShare on Twitter

Comments

  • txcoastal1
    txcoastal1 Posts: 13,285
    If Polk doesn't support it

    Post a pic of it and more than likely we can help you get it fixed or you van fix yourself

    Can you see any burned up stuff like a white block looking thing...(sandcast resistor)
    2-channel: Modwright KWI-200 Integrated, Dynaudio C1-II Signatures
    Desktop rig: LSi7, Polk 110sub, Dayens Ampino amp, W4S DAC/pre, Sonos, JRiver
    Gear on standby: Melody 101 tube pre, Unison Research Simply Italy Integrated
    Gone to new homes: (Matt Polk's)Threshold Stasis SA12e monoblocks, Pass XA30.5 amp, Usher MD2 speakers, Dynaudio C4 platinum speakers, Modwright LS100 (voltz), Simaudio 780D DAC

    erat interfectorem cesar et **** dictatorem dicere a
    · Share on FacebookShare on Twitter
  • Topher0384
    Topher0384 Posts: 3
    9p75xugbig1a.jpg
    qg7988cqxxyy.jpg
    yl93xz6h9h03.jpg
    d6dxc9optsjx.jpg
    · Share on FacebookShare on Twitter
  • txcoastal1
    txcoastal1 Posts: 13,285
    Don't see anything terribly nasty, are you sure it the xover?
    Reason I ask, is the whole speaker not putting out signal, or maybe just a driver/tweeter
    2-channel: Modwright KWI-200 Integrated, Dynaudio C1-II Signatures
    Desktop rig: LSi7, Polk 110sub, Dayens Ampino amp, W4S DAC/pre, Sonos, JRiver
    Gear on standby: Melody 101 tube pre, Unison Research Simply Italy Integrated
    Gone to new homes: (Matt Polk's)Threshold Stasis SA12e monoblocks, Pass XA30.5 amp, Usher MD2 speakers, Dynaudio C4 platinum speakers, Modwright LS100 (voltz), Simaudio 780D DAC

    erat interfectorem cesar et **** dictatorem dicere a
    · Share on FacebookShare on Twitter
  • Topher0384
    Topher0384 Posts: 3
    Drivers are fine, put the tweeter in the other power and it works fine. If i put the input from the amp in the out put part of the tweeter it works. But once I hook it up to the wire terminals I get nothings.
    · Share on FacebookShare on Twitter
  • txcoastal1
    txcoastal1 Posts: 13,285
    Polk may still support replacement xovers, but if not post back and leave their response. Maybe someone has parts or speakers to let go to get them back up and running.

    Call Polk Customer service vs emailing them.

    You can search hifi shark to see if any for sale on the cheap

    Sorry couldn't help

    2-channel: Modwright KWI-200 Integrated, Dynaudio C1-II Signatures
    Desktop rig: LSi7, Polk 110sub, Dayens Ampino amp, W4S DAC/pre, Sonos, JRiver
    Gear on standby: Melody 101 tube pre, Unison Research Simply Italy Integrated
    Gone to new homes: (Matt Polk's)Threshold Stasis SA12e monoblocks, Pass XA30.5 amp, Usher MD2 speakers, Dynaudio C4 platinum speakers, Modwright LS100 (voltz), Simaudio 780D DAC

    erat interfectorem cesar et **** dictatorem dicere a
    · Share on FacebookShare on Twitter