JB Weld, where to put it!

kjack48230
kjack48230 Posts: 15
in Vintage Speakers
Can someone upload a picture of exactly where you place the JB Weld? Want to make sure I'm doing this right! Thanks in advance.
· Share on FacebookShare on Twitter

Comments

  • trj
    trj Posts: 320
    Just dont put it on your food :smile:
    Sony BDP-S6500 | Raspberry Pi 2 | XBOX One S | Wii --> Yamaha RX-V667 --> Adcom 5006 bridged to 175 watts for front LCR -- >Front: Polk Audio RTi8s | Center: CSi5 | Side Surrounds: RTi4s | Rear surrounds: FXiA4s | Cheap 12" sub woofer|Samsung UN60KU6300
    · Share on FacebookShare on Twitter
  • Gatecrasher
    Gatecrasher Posts: 1,550
    I can think of a couple other places I wouldn't want to put it.
    · Share on FacebookShare on Twitter
  • Dennis Gardner
    Dennis Gardner Posts: 4,861
    edited April 2016
    There are pics and diagrams on this thread on magnet repair. The pics are hard to see as they used Loctite Clear instead of JB Weld. forum.polkaudio.com/discussion/comment/2224925#Comment_2224925

    Apply a bead of Loctite/JB Weld where the front plate meets the magnet, and where the back plate meets the magnet.
    HT Optoma HD25 LV on 80" DIY Screen, Anthem MRX 300 Receiver, Pioneer Elite BDP 51FD Polk CS350LS, Polk SDA1C, Polk FX300, Polk RT55, Dual EBS Adire Shiva 320watt tuned to 17hz, ICs-DIY Twisted Prs, Speaker-Raymond Cable

    2 Channel Thorens TD 318 Grado ZF1, SACD/CD Marantz 8260, Soundstream/Krell DAC1, Audio Mirror PP1, Odyssey Stratos, ADS L-1290, ICs-DIY Twisted , Speaker-Raymond Cable
    · Share on FacebookShare on Twitter
  • boston1450
    boston1450 Posts: 7,637
    See this magnet. Im gonna put a bead on each side (this is a cerwin vega 15)ln42vy5loeww.jpeg
    ..
    · Share on FacebookShare on Twitter
  • boston1450
    boston1450 Posts: 7,637
    Done c22slk9fnb5n.jpeg
    ..
    · Share on FacebookShare on Twitter
  • HzTweaker
    HzTweaker Posts: 785
    This is very good information. I don't know how I missed the bit that instructs you to apply to the rear plate. I'm sort of aggravated at myself because I only applied between the front plat and the mag. . Is it possible for the rear plate to shift?
    2ch rig: Speakers: Magnepan LRS w/Magna Riser stands Preamplifier: Parasound P5 Amplifier: Parasound A23 CDP: Pioneer DV-563A Cables: Wireworld Equinox 7 XLR ICs, Wireworld Ultraviolet 7 USB, AudioQuest Q2s, AudioQuest NRG X(preamp)

    Standby: LSi9s with VR3's Fortress mods
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,550
    Yes
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • HzTweaker
    HzTweaker Posts: 785
    Well it looks like I've a good Sunday project ahead of me.
    2ch rig: Speakers: Magnepan LRS w/Magna Riser stands Preamplifier: Parasound P5 Amplifier: Parasound A23 CDP: Pioneer DV-563A Cables: Wireworld Equinox 7 XLR ICs, Wireworld Ultraviolet 7 USB, AudioQuest Q2s, AudioQuest NRG X(preamp)

    Standby: LSi9s with VR3's Fortress mods
    · Share on FacebookShare on Twitter