Installing Larry's rings on the PR
![[Deleted User]](https://wc.vanillicon.com/c42e30d069c0d43c9bdf07a3e4e17a6d_100.png)
[Deleted User]
Posts: 365
How do you install the PR ring , if they are suppose to be on the inside? What is my feeble mind missing? Also, do you just put the foam behind the mid drivers and not on the top or sides ? Thanks!
Comments
-
Do you have to unbolt the bottom piece ?
-
The PR ring has two slots cut out. You bend the ring at those two spots just enough to slip it through the cabinet hole, then bend it back flat.
BH5 or the like goes just behind the mid-drivers.....didn't I already spell that out to you?Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."
President of Club Polk -
I sure don't see any slots on mine. Yes, you did spell it out. Thanks!
-
As I recall, mine just had two black marks on opposite sides, it bends very easy over a straight edge.VA HT HK AVR20II, Sony S9000ES CD/DVD/SACD, Polk Audio RC80i / Polk Audio CSi3, 60" Panasonic Plasma, Nordost / Signal Cable A2 / Wireworld / Pangea / Magic Power
VA 2 Channel Focal Electra 926 speakers, Pass Labs X150.5 Amp, Eastern Electric MiniMax Preamp (Tutay mods), Eastern Electric Minimax CDP (Scott Nixon mods), Music Hall mmf 5.1 Turntable, Parks Audio Budgie Phono Pre , Audioengine B1 streamer, MIT S3 IC's / MIT Shotgun S3 Speaker Cables / PS Audio power cables
Noggin Schiit Valhalla, Pangea, Phillips Fidelio X1, Polk UF8000
Polk SDA1c modded
Polk CRS+ 4.1TL modded (need veneer)
Polk SDA2BTL (fully modded)
A/L 1000VA Dreadnought Canare 4s11 SDA cable
SACD Marantz DV8300
Sony S9000ES CD/DVD/SACD
Yamaha YP-D6
Soundcraftsmen PCR800
Audible Illusions L1 Preamp
Vincent MFA based Cocci Tube Preamp
Pho-700 Phono Pre
Signal Cable Silver Resolution IC's -
Mine did not have slots. But as mentioned above I just flexed it into the cabinet.
One thing to note is that I did have to reduce the height of the threaded inserts so that they set below the surface that the passive seats against. I did this with a belt sander.Mojo Audio Illuminati v3>>Quantum Byte w/LMS>>Rpi/PiCoreplayer>> Starlight 7 USB >> Mojo Audio Mystique v2 SE>>ModWright SWL 9.0 SE Signature>>Hafler DH-500 Amp+ (Musical Concepts Fully Modded)>>
SRS 2.3TL (Fully Modded)...Velodyne Optimum 8 subwoofer
1KVA Dreadnought
Marantz SA 8005
Pioneer PLX-1000 Turntable - Shure SC35C/N35X - V15III/VN35HE
Yamaha TX-540 Tuner...Sony BDP-S570
Sony PS4
Separate subpanel with four dedicated 20 amp circuits.
1. Amplification 2. Analog 3. Digital 4. Video
"All THAT IS LOST FROM THE SOURCE IS LOST FOREVER" -
I sure was over thinking that one. One side all done. I'm sure the other side will take much less time.
-
^^ haha! ^^ I remember thinking the same thing!
VA HT HK AVR20II, Sony S9000ES CD/DVD/SACD, Polk Audio RC80i / Polk Audio CSi3, 60" Panasonic Plasma, Nordost / Signal Cable A2 / Wireworld / Pangea / Magic Power
VA 2 Channel Focal Electra 926 speakers, Pass Labs X150.5 Amp, Eastern Electric MiniMax Preamp (Tutay mods), Eastern Electric Minimax CDP (Scott Nixon mods), Music Hall mmf 5.1 Turntable, Parks Audio Budgie Phono Pre , Audioengine B1 streamer, MIT S3 IC's / MIT Shotgun S3 Speaker Cables / PS Audio power cables
Noggin Schiit Valhalla, Pangea, Phillips Fidelio X1, Polk UF8000
Polk SDA1c modded
Polk CRS+ 4.1TL modded (need veneer)
Polk SDA2BTL (fully modded)
A/L 1000VA Dreadnought Canare 4s11 SDA cable
SACD Marantz DV8300
Sony S9000ES CD/DVD/SACD
Yamaha YP-D6
Soundcraftsmen PCR800
Audible Illusions L1 Preamp
Vincent MFA based Cocci Tube Preamp
Pho-700 Phono Pre
Signal Cable Silver Resolution IC's
