Polk audio sda 1c

bcfd44
bcfd44 Posts: 2
in Basic Hookup/Wiring Questions
Wondering if any one have a set of interconnect cables for polk audio sda 1c, which require the pin and blade cord. I've been looking everywhere for theses. Willing to pay. Thanks
· Share on FacebookShare on Twitter

Best Answer

  • Easy Runnin
    Easy Runnin Posts: 501
    Answer ✓
    Here is the first cable I made. I've since upgraded to speakons

    71sykxu1ehu8.jpg
    HT- Samsung PN50B860/Integra DTR 30.3/Rt55 Fronts
    Rt35i Surrounds/Cs1000p Center/SVS BP1000 Sub
    2CH - B&K MC-101 pre/B&K EX-442 amp/NAD 2400 amp
    Polk SDA1C, Polk Monitor 7, New Large Advents and Polk RTA 8T
    BR - Yamaha CR800/Polk monitor 5
    · Share on FacebookShare on Twitter

Answers

  • Easy Runnin
    Easy Runnin Posts: 501
    I made my own. Do a search on making your own. You can buy a length of cooper at Home Depot that is the exact size you need for the pin, attached that to a lenght of cable and your good to go. it's pretty easy. the blade connection was only for support
    HT- Samsung PN50B860/Integra DTR 30.3/Rt55 Fronts
    Rt35i Surrounds/Cs1000p Center/SVS BP1000 Sub
    2CH - B&K MC-101 pre/B&K EX-442 amp/NAD 2400 amp
    Polk SDA1C, Polk Monitor 7, New Large Advents and Polk RTA 8T
    BR - Yamaha CR800/Polk monitor 5
    · Share on FacebookShare on Twitter
  • voltz
    voltz Posts: 5,384
    Agree, you could make one or others could make one for you. welcome to the forum and do some reading in the Vintage part of this forum where others are always talking about their SDA 1C's and other SDA's...lots of good reading in there if you look deep enough!
    2 ch- Polk CRS+ * Vincent SA-31MK Preamp * Vincent Sp-331 Amp * Marantz SA8005 SACD * Project Xperience Classic TT * Sumiko Blue Point #2 MC cartridge

    HT - Polk 703's * NAD T-758 * Adcom 5503 * Oppo 103 * Samsung 60" series 8 LCD
    · Share on FacebookShare on Twitter
  • bcfd44
    bcfd44 Posts: 2
    Thanks for your response
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,647
    Do away with the pin/blade stuff and replace with SpeakOn connections, far better quality.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • PolkieMan
    PolkieMan Posts: 2,446
    edited March 2015
    You can make one from these two items and use the wire left over for new standard speaker cables. Just break off or dremel the outer lugs leaving only the center pin.


    http://www.monoprice.com/Product?c_id=102&cp_id=10239&cs_id=1023901&p_id=2816&seq=1&format=2


    http://www.monoprice.com/Product?c_id=104&cp_id=10424&cs_id=1042404&p_id=6212&seq=1&format=2

    POLK SDA 2.3 TLS BOUGHT NEW IN 1990, Gimpod/Sonic Caps/Mills RDO-198
    POLK CSI-A6 POLK MONITOR 70'S ONKYO TX NR-808 SONY CDP-333ES
    PIONEER PL-510A SONY BDP S5100
    POLK SDA 1C BOUGHT USED 2011,Gimpod/Sonic Caps/Mills RDO-194
    ONKYO HT RC-360 SONY BDP S590 TECHNICS SL BD-1
    · Share on FacebookShare on Twitter