Hurricane Nuts
Faustin
Posts: 1,149
Looking for advise on using hurricane nuts and machine screws on larger passive radiators. Most of the original pr's use only 4 of 8 holes to fasten the pr to the cabinet. Is it recommended to use all 8 holes and drill out and install hurricane nuts, or just use the 4?
Post edited by Faustin on
Comments
-
I'm sure you would be fine with just the four, but myself would do all eight...Polk Audio SDA 2.3tl Fully Hot Rodded. 😎
SVS SB16 X2
Cary SLP-05/Ultimate Upgrade.
Cary SA-500.1 ES Amps
Cary DMS 800PV Network
OPPO UDP 205/ModWright Modification
VPI Scout TT / Dynavector 20x2
Jolida JD9 Fully Modified
VPI MW-1 Cyclone RCM
MIT Shotgun 3 cables throughout / Except TT, and PC’s -
Other than the CRS/CRS+, what other SDA's only use 4 of the 8?
Anyway, do all 8.Political Correctness'.........defined
"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."
President of Club Polk -
Other than the CRS/CRS+, what other SDA's only use 4 of the 8?
Anyway, do all 8.
That's the only one, but all the monitors use 4, but I know you know that.. LOL!!! :-)Polk Audio SDA 2.3tl Fully Hot Rodded. 😎
SVS SB16 X2
Cary SLP-05/Ultimate Upgrade.
Cary SA-500.1 ES Amps
Cary DMS 800PV Network
OPPO UDP 205/ModWright Modification
VPI Scout TT / Dynavector 20x2
Jolida JD9 Fully Modified
VPI MW-1 Cyclone RCM
MIT Shotgun 3 cables throughout / Except TT, and PC’s -
Thanks for the input. Spaecifically it would be for monitor 10's and RTA 12's.
-
Yep, use all available holes. You'll get much better coupling of the PR to the front baffle, less chance for air leaks."Science is suppose to explain observations not dismiss them as impossible" - Norm on AA; 2.3TL's w/sonicaps/mills/jantzen inductors, Gimpod's boards, Lg Solen SDA inductors, RD-0198's, MW's dynamatted, Armaflex speaker gaskets, H-nuts, brass spikes, Cardas CCGR BP's, upgraded IC Cable, Black Hole Damping Sheet strips, interior of cabinets sealed with Loctite Power Grab, AI-1 interface with 1000VA A-L transformer
-
Just received an order of hurricane nuts from PE. They stick to a magnet. I thought I read somewhere in here that this is a problem? What's the scoop? Thanks
-
Just received an order of hurricane nuts from PE. They stick to a magnet. I thought I read somewhere in here that this is a problem? What's the scoop? Thanks
It’s not a problem... Rock On.....
Polk Audio SDA 2.3tl Fully Hot Rodded. 😎
SVS SB16 X2
Cary SLP-05/Ultimate Upgrade.
Cary SA-500.1 ES Amps
Cary DMS 800PV Network
OPPO UDP 205/ModWright Modification
VPI Scout TT / Dynavector 20x2
Jolida JD9 Fully Modified
VPI MW-1 Cyclone RCM
MIT Shotgun 3 cables throughout / Except TT, and PC’s -
Polk Audio SDA 2.3tl Fully Hot Rodded. 😎
SVS SB16 X2
Cary SLP-05/Ultimate Upgrade.
Cary SA-500.1 ES Amps
Cary DMS 800PV Network
OPPO UDP 205/ModWright Modification
VPI Scout TT / Dynavector 20x2
Jolida JD9 Fully Modified
VPI MW-1 Cyclone RCM
MIT Shotgun 3 cables throughout / Except TT, and PC’s -
Domo arigato, Larry-san.