Part (s) needed for my Sda-SRS speakers. Same part on several different speakers.

oldmodman
oldmodman Posts: 740
edited July 2013 in Vintage Speakers
Does anyone know where I can buy a few of the plastic pegs on the front panel of the cabinet that the grill pushes onto?

There are three of them broken off flush with the surface of the cabinet.

The speakers are an SDA-SRS 2.3 (might be a tl but it had the donuts on the upper woofer and doesn't say "tl" on the serial number plate on the rear) and a SDA-SRS 3.1.tl
Post edited by oldmodman on
· Share on FacebookShare on Twitter

Comments

  • Toolfan66
    Toolfan66 Posts: 17,243
    edited July 2013
    I might have some, I will look when I get home..
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,557
    edited July 2013
    Parts Express sells them. Although they are slightly different in size, they work and are the closest anyone has ever found to the originals.
    might be a tl but it had the donuts on the upper woofer

    They are not TL's.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • oldmodman
    oldmodman Posts: 740
    edited July 2013
    Toolfan66 wrote: »
    I might have some, I will look when I get home..

    Thank you very much. I had called Polk Service but didn't get an answer. I figured that would be either the same part used today or long discontinued.
    · Share on FacebookShare on Twitter
  • oldmodman
    oldmodman Posts: 740
    edited July 2013
    F1nut wrote: »
    Parts Express sells them. Although they are slightly different in size, they work and are the closest anyone has ever found to the originals.
    They are not TL's.

    Thanks.
    I'll look for them on their site.
    And I was pretty sure that they were not "tl's" since they have the older tweeter and the donut on one woofer. When I refer to them what is the correct name? Just SDA-SRS 2.3?
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,557
    edited July 2013
    And I was pretty sure that they were not "tl's" since they have the older tweeter and the donut on one woofer.

    They should have two donut drivers per cabinet. One in the top position and one on the bottom. Both should be labeled MW6513.
    When I refer to them what is the correct name? Just SDA-SRS 2.3?

    Yes.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • soundfreak1
    soundfreak1 Posts: 3,414
    edited July 2013
    If toolfan dosent have any i should have someleft. How many do u need?
    Main Rig:
    Krell KAV 250a biamped to mid/highs
    Parasound HCA1500A biamped to lows
    Nakamichi EC100 Active xover
    MIT exp 1 ic's
    Perreaux SA33 class A preamp
    AQ kingcobra ic's
    OPPO 83 CDP
    Lehmann audio black cube SE phono pre, Audioquest phono wire (ITA1/1)
    Denon DP-1200 TT. AToc9ML MC cart.
    Monster HTS 3600 power conditioner
    ADS L1590/2 Biamped
    MIT exps2 speaker cable
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,243
    edited July 2013
    Crap, I forgot to look when I got home last night..

    Will do this afternoon..
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,442
    edited July 2013
    F1nut wrote: »
    Parts Express sells them. Although they are slightly different in size, they work and are the closest anyone has ever found to the originals..

    Are they different on the upper speakers? I bought some from Parts Express for my SDA1's and they are perfect in all regards to the factory pegs.
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,557
    edited July 2013
    Are they different on the upper speakers?

    I'm not entirely sure. What I found is that they fit the hole perfectly, but the ball end is slightly smaller, so they don't grip the grill as tightly as the originals.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,243
    edited July 2013
    For the record oldmodman, if I have these/if I can find them LOL!!! they are yours free of charge..
    · Share on FacebookShare on Twitter
  • Malbec
    Malbec Posts: 553
    edited July 2013
    Hey Larry, while you're looking in your stash see if you have any crossover plate rings you can part with.
    · Share on FacebookShare on Twitter
  • oldmodman
    oldmodman Posts: 740
    edited July 2013
    That's a very nice offer.

    PM coming your way.
    · Share on FacebookShare on Twitter