Trey - any more binding post cup replacements left?

nspindel
nspindel Posts: 5,343
edited June 2013 in DIY, Mods & Tweaks
Thinking down the road I may do the replacement wiring harnesses for the internal wiring of my 4.1 TL's. At that point I'll need to de-solder the binding posts anyway, so it would be a perfect time to swap out the plastic cup for your new plate. Do you still have a pair available?
Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
Post edited by nspindel on
· Share on FacebookShare on Twitter

Comments

  • VR3
    VR3 Posts: 28,746
    edited May 2013
    I am having a new batch made, will be all VR3 Mods branded though.

    Will be available in two weeks or so I hope.
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • nspindel
    nspindel Posts: 5,343
    edited May 2013
    I would be PROUD to have VR3 Mods displayed on my SDA's!!!!

    On the back.... Where no one will see it!!! :razz:


    Just kidding, count me in for a pair!
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited May 2013
    Sounds good,
    The pricing will be a bit different this time.

    Will keep everyone posted... :]
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • Aragon8008
    Aragon8008 Posts: 10
    edited June 2013
    How hard is it to change binding posts on an amp?
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,570
    edited June 2013
    Can you solder?
    · Share on FacebookShare on Twitter
  • codyc1ark
    codyc1ark Posts: 2,532
    edited June 2013
    Dogg, I think we have a spammer here. Brand new, and ten posts in ten minutes? Hmmm... Anyway, this thread doesnt have anything to do with binding posts on amp.
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,570
    edited June 2013
    codyc1ark wrote: »
    Dogg, I think we have a spammer here. Brand new, and ten posts in ten minutes? Hmmm... Anyway, this thread doesnt have anything to do with binding posts on amp.

    Well I gave him the benefit of the doubt. I was watching him post like mad he even brought up a old thread on replacing binding post. so i hit him up. We'll see if he comes back.
    take care
    · Share on FacebookShare on Twitter
  • nspindel
    nspindel Posts: 5,343
    edited June 2013
    Trey, do you have a date for these yet? Thanks!
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited June 2013
    I do not, I am having to change how they made. It will take longer but the good news is they should look incredible. Even more so than before.
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited June 2013
    lol, not much better. That was the first batch essentially, I am always trying to improve... :)

    I would not sell anything I was not proud of...
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • nspindel
    nspindel Posts: 5,343
    edited June 2013
    Question - are your binding post cup replacements able to accept a binding post as the replacement for the SDA connector? I know people were using speakon connectors instead of binding posts, but my Dreadnaught cables use plain old binding post connections. Not sure what size the hole for a speakon is vs. a hole for a binding post. Doable?
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited June 2013
    With the new shop that will not be a problem
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • nspindel
    nspindel Posts: 5,343
    edited June 2013
    Perfect!
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited June 2013
    We also will be able to offer powder coating, at a premium - any color pretty much :)
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited June 2013
    Excellent news today - I saw a prototype of the plates that the new shop is working with me on and I am pretty stoked to bring these to the table -

    They are going to be thicker with a machine grained mirror finish versus the hand grain finish
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • nspindel
    nspindel Posts: 5,343
    edited June 2013
    Pretty cool. What's the eta?
    Good music, a good source, and good power can make SDA's sing. Tubes make them dance.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,746
    edited June 2013
    2 weeks.

    Unfortunately I am having to use two shops, one for the milling and one for the printing.

    I can assure you though the quality will be through the roof :)
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter