Stand for CiA6

pablo_rodz
pablo_rodz Posts: 331
edited December 2012 in Speakers
I'm putting together my home theater, and need suggestions for a center channel stand. I've done some researching, but the stands I've seen seem small for the CiA6.

The speaker will be placed below a 100" screen.

Thanks in advance.
HT:
Projector - JVC HD100, 100" Fixed Screen, A/V Receiver - Pioneer Elite VSX-92TXH, Power Conditioner - Panamax M5300-EX, BluRay - Sony PS3, (2) ADCOM GFA 555 Bridged, Speakers - LSi 15, LSi C, LSi FX, Sub - 12" M&K VX-1250.

Living Room:
Schiit Saga, Parasound HCA-600, OPPO BDP-103D, LSi7
Post edited by pablo_rodz on
· Share on FacebookShare on Twitter

Comments

  • ken brydson
    ken brydson Posts: 8,783
    edited December 2012
    Stand just for the center or other gear as well?
    · Share on FacebookShare on Twitter
  • Toxis
    Toxis Posts: 5,116
    edited December 2012
    Sanus has a couple center channel stands. 18" or 22" tall and you can fill the legs with shot/sand if you need to stabilize it.

    http://www.sanus.com/us/en/products/speaker-foundations/sp-steel/SFC18

    http://www.sanus.com/us/en/products/speaker-foundations/sp-steel/SFC22
    Never kick a fresh **** on a hot day.

    Home Setup: Sony VPL-VW85 Projo, 92" Stewart Firehawk, Pioneer Elite SC-65, PS3, RTi12 fronts, CSi5, FXi6 rears, RTi6 surround backs, RTi4 height, MFW-15 Subwoofer.

    Car Setup: OEM Radio, RF 360.2v2, Polk SR6500 quad amped off 4 Xtant 1.1 100w mono amps, Xtant 6.1 to run an eD 13av.2, all Stinger wiring and Raammat deadener.
    · Share on FacebookShare on Twitter
  • PolkieMan
    PolkieMan Posts: 2,446
    edited December 2012
    I just went down to Lowe's and bought a shelve 36 x 12 and two brackets for my CsiA6


    100_030612.jpg
    POLK SDA 2.3 TLS BOUGHT NEW IN 1990, Gimpod/Sonic Caps/Mills RDO-198
    POLK CSI-A6 POLK MONITOR 70'S ONKYO TX NR-808 SONY CDP-333ES
    PIONEER PL-510A SONY BDP S5100
    POLK SDA 1C BOUGHT USED 2011,Gimpod/Sonic Caps/Mills RDO-194
    ONKYO HT RC-360 SONY BDP S590 TECHNICS SL BD-1
    · Share on FacebookShare on Twitter
  • pablo_rodz
    pablo_rodz Posts: 331
    edited December 2012
    Polkie, do you have a picture of it?

    I've seen the sanus, I like the steel foundation collection, but the "shelf" piece is smaller than the speaker. I was worried of the stability and proper support.
    HT:
    Projector - JVC HD100, 100" Fixed Screen, A/V Receiver - Pioneer Elite VSX-92TXH, Power Conditioner - Panamax M5300-EX, BluRay - Sony PS3, (2) ADCOM GFA 555 Bridged, Speakers - LSi 15, LSi C, LSi FX, Sub - 12" M&K VX-1250.

    Living Room:
    Schiit Saga, Parasound HCA-600, OPPO BDP-103D, LSi7
    · Share on FacebookShare on Twitter
  • DAVE HOFFER
    DAVE HOFFER Posts: 23
    edited December 2012
    I would build a wood stand out of pine board. Make it the height and with you need and paint it black. Look like a side ways H with 2 offsets supports in the middle. Cheap and affective. Just my thoughts.
    · Share on FacebookShare on Twitter
  • oleon621
    oleon621 Posts: 178
    edited December 2012
    If your handy you could build it yourself with simple tools. Strongly suggest you get all you measurements/drawings on paper and get to cutting ;)
    Front- RTI A7,(powered by ADCOM GFA 5500)
    Center- CSI5,
    Surrounds- RTI 6 and Rear Surrounds- TS 15.
    TV-Panasonic P55ST50
    SUB-SVS PB10-NSD and PSW505
    Receiver- Yamaha Aventage RX-A2000
    · Share on FacebookShare on Twitter