PIONEER ELITE SC07 preouts issue

doggie750
doggie750 Posts: 1,160
edited August 2012 in Electronics
Hello Polks,
Shout out to the ICE club peeps here, my original SC07 was stolen when I had it service for firmware upgrade. The authorized service center replaced it with a used one with 1month warranty. So now I am screwed, most of the preouts are F>>King loose, no signal coming out (you have to move it around 'till u can achieve signal) I assume this came from a store and ran as display and abused. Seem like the fools from the store dont know how to use the interconnects correctly.

Panel was removed to investigate but it aint service friendly, covered with IC boards, so seeking some advice here. I guess i can disconnect some IC boards to gain access to the connectors and resolder.....:question:
Godspeed,
D0661E

AVR:Pioneer Elite SC-07
Surrounds: RTis
2channel:Rti100 (carver driven
Sub:SVS PB12-Plus/2
Dedicated AMPs:Adcom GFA535, 2xCarver 1.5t, Carver m1.0t
Wsrn:Hitachi ultra vision LCD60, 32XBR400
PowerConditioner: MonsterC HTS5100
PS3, Toshiba HD A2, etc: SonySACD/ Panasonic gears DIVX.

MR3LIGION: Polkaudio; GSXR; E46; Reeftank;
Odyclub; Xsimulator; Sony; Zune; Canon
Post edited by doggie750 on
· Share on FacebookShare on Twitter

Comments

  • disneyjoe7
    disneyjoe7 Posts: 11,435
    edited August 2012
    It seems to me that you're correct they need to be resoldered. Could you do this? If not resend it back to fix them.

    Speakers
    Carver Amazing Fronts
    CS400i Center
    RT800i's Rears
    Sub Paradigm Servo 15

    Electronics
    Conrad Johnson PV-5 pre-amp
    Parasound Halo A23
    Pioneer 84TXSi AVR
    Pioneer 79Avi DVD
    Sony CX400 CD changer
    Panasonic 42-PX60U Plasma
    WMC Win7 32bit HD DVR


    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,569
    edited August 2012
    Tell them you want cash, not the piece of junk they are trying to pass off.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • gfong
    gfong Posts: 1,079
    edited August 2012
    If it's a service center can they not fix it to at least the shape yours was in when they recieved it? I would also look into cash as it sounds like you got the worst end of this deal. They just happened to have one on the shelf eh! hmmmm. :)
    · Share on FacebookShare on Twitter
  • doggie750
    doggie750 Posts: 1,160
    edited August 2012
    Unfortunately, 1month warranty has been passed. They'll charge $50-60/hr to fix depending on the case. As noted, I am screwed. Been watching movies w/o my amps and sub :(
    Godspeed,
    D0661E

    AVR:Pioneer Elite SC-07
    Surrounds: RTis
    2channel:Rti100 (carver driven
    Sub:SVS PB12-Plus/2
    Dedicated AMPs:Adcom GFA535, 2xCarver 1.5t, Carver m1.0t
    Wsrn:Hitachi ultra vision LCD60, 32XBR400
    PowerConditioner: MonsterC HTS5100
    PS3, Toshiba HD A2, etc: SonySACD/ Panasonic gears DIVX.

    MR3LIGION: Polkaudio; GSXR; E46; Reeftank;
    Odyclub; Xsimulator; Sony; Zune; Canon
    · Share on FacebookShare on Twitter
  • pitdogg2
    pitdogg2 Posts: 25,453
    edited August 2012
    better business bureau is your friend they gave you a lemon and they knew it they should work with you.....
    · Share on FacebookShare on Twitter
  • blairfrischx
    blairfrischx Posts: 259
    edited August 2012
    pitdogg2 wrote: »
    better business bureau is your friend they gave you a lemon and they knew it they should work with you.....

    Just think of it as building appreciation for your system? :cheesygrin:
    · Share on FacebookShare on Twitter