RTi70 with LSiC compatibility

doggie750
doggie750 Posts: 1,160
edited July 2012 in Speakers
Would like to upgrade my CSi30 to LsiC but a little concern on soundstage balance with RTi70, Fxi surrounds. Please advice. Thank you polks. My assumption that this should work w/o issue.
Godspeed,
D0661E

AVR:Pioneer Elite SC-07
Surrounds: RTis
2channel:Rti100 (carver driven
Sub:SVS PB12-Plus/2
Dedicated AMPs:Adcom GFA535, 2xCarver 1.5t, Carver m1.0t
Wsrn:Hitachi ultra vision LCD60, 32XBR400
PowerConditioner: MonsterC HTS5100
PS3, Toshiba HD A2, etc: SonySACD/ Panasonic gears DIVX.

MR3LIGION: Polkaudio; GSXR; E46; Reeftank;
Odyclub; Xsimulator; Sony; Zune; Canon
Post edited by doggie750 on
· Share on FacebookShare on Twitter

Comments

  • VR3
    VR3 Posts: 28,781
    edited July 2012
    It would work but the LSiC is a superior speaker...
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,781
    edited July 2012
    Have you considered purchasing the used set of RTi38 for sale in the flea market and using those as center channels?

    Just put the tweeters together... that's less than 2 bills!
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • doggie750
    doggie750 Posts: 1,160
    edited July 2012
    I have a pair of RTi38 as surrounds, might have to try this out. What's the setting, // connect ? Will this be better than LsiC alone?
    Godspeed,
    D0661E

    AVR:Pioneer Elite SC-07
    Surrounds: RTis
    2channel:Rti100 (carver driven
    Sub:SVS PB12-Plus/2
    Dedicated AMPs:Adcom GFA535, 2xCarver 1.5t, Carver m1.0t
    Wsrn:Hitachi ultra vision LCD60, 32XBR400
    PowerConditioner: MonsterC HTS5100
    PS3, Toshiba HD A2, etc: SonySACD/ Panasonic gears DIVX.

    MR3LIGION: Polkaudio; GSXR; E46; Reeftank;
    Odyclub; Xsimulator; Sony; Zune; Canon
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,781
    edited July 2012
    Just run them in paralle (+ to +, - to -) Make sure your amp can handle a 4 ohm load
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • hertz9753
    hertz9753 Posts: 310
    edited July 2012
    VR3 wrote: »
    Just run them in paralle (+ to +, - to -) Make sure your amp can handle a 4 ohm load

    Wouldn't that create a 2 omh load?
    AVR-Onkyo TX-NR808
    Front amp-Adcom GFA 555>Polk Audio LSi9's(Vr3 Castle Mods)
    Center amp-Adcom GFA 5400>Polk Audio LSi9 bi-wired(Vr3 Castle Mod)
    Surrounds-Polk Audio F/X500's<Onkyo TX-NR808
    Sub-Velodyne SPL-1000R
    · Share on FacebookShare on Twitter
  • VR3
    VR3 Posts: 28,781
    edited July 2012
    The RTi38 is an 8 ohm speaker
    - Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
    · Share on FacebookShare on Twitter
  • hertz9753
    hertz9753 Posts: 310
    edited July 2012
    VR3 wrote: »
    The RTi38 is an 8 ohm speaker

    I read the whole thread, but it seems I got lost without quotes. :razz:
    AVR-Onkyo TX-NR808
    Front amp-Adcom GFA 555>Polk Audio LSi9's(Vr3 Castle Mods)
    Center amp-Adcom GFA 5400>Polk Audio LSi9 bi-wired(Vr3 Castle Mod)
    Surrounds-Polk Audio F/X500's<Onkyo TX-NR808
    Sub-Velodyne SPL-1000R
    · Share on FacebookShare on Twitter