SDA-SRS... what first?
Denzel
Posts: 78
Just got pair of SDA-SRS locally in Wichita, KS. (circa 1988, originals not 1.2's) these are a little different than my 2.3's that I modded last year, what should I do first? rebuild xovers? new tweeters? They are blade/blade interconnect, so if i replace the interconnect connector like I did on my 2.3's do I need to have both blades connected, or is one a stabilizer like on the pin/blade version? They are pretty much in perfect original condition. They fire up and sound great, but I thpought the same about my 2.3's until I had the crossovers rebuilt and tweeters replaced, so I am excited to breathe new life into these.
Much appreciation ahead of time for all your advice & guidance.
Much appreciation ahead of time for all your advice & guidance.
SDA SRS 3.1TL, Adcom GFP710 (preamp), GFA5400 amplifier, Pro-Ject TT
SDA SRS (circa 1988), Integra DHC 60.3 (HT preamp) Adcom GFA555 II, CS400i (center), Monitor 4.6 II (rears) Adcom GFA2535 & Oppo BDP-103, TCL 55R617 55" 4K Display, RTA 15TL (crossovers by VR3), Adcom GFP710 pre & GFA545 II amplifier, NAD C545BEE. AppleTV 4K
Other Polks not in service currently; SDA2a, SDA CRS+, SDA SRS 2.3, Monitor 4.6 II, Monitor 5jr+
SDA SRS (circa 1988), Integra DHC 60.3 (HT preamp) Adcom GFA555 II, CS400i (center), Monitor 4.6 II (rears) Adcom GFA2535 & Oppo BDP-103, TCL 55R617 55" 4K Display, RTA 15TL (crossovers by VR3), Adcom GFP710 pre & GFA545 II amplifier, NAD C545BEE. AppleTV 4K
Other Polks not in service currently; SDA2a, SDA CRS+, SDA SRS 2.3, Monitor 4.6 II, Monitor 5jr+
Post edited by Denzel on
Comments
-
Blade/ Blade interconnects use both blades you need both. When I recapped on my B/B speakers I sealed the B/B connector with hot glue and put in good binding posts for the interconnect made a good difference over stock.
-
replace blade with xlr connection...- Not Tom ::::::: Any system can play Diana Krall. Only the best can play Limp Bizkit.
-
Aha, didnt consider XLR for a two wire connection... and yes I am going to overhaul the binding posts wth CARDAS.
Thanks fellas.SDA SRS 3.1TL, Adcom GFP710 (preamp), GFA5400 amplifier, Pro-Ject TT
SDA SRS (circa 1988), Integra DHC 60.3 (HT preamp) Adcom GFA555 II, CS400i (center), Monitor 4.6 II (rears) Adcom GFA2535 & Oppo BDP-103, TCL 55R617 55" 4K Display, RTA 15TL (crossovers by VR3), Adcom GFP710 pre & GFA545 II amplifier, NAD C545BEE. AppleTV 4K
Other Polks not in service currently; SDA2a, SDA CRS+, SDA SRS 2.3, Monitor 4.6 II, Monitor 5jr+ -
Here's what I'm planning on using for my b/b 1c's
http://www.thecableco.com/Product/XLR-CF-Chassis-Mount-XLR--Set-of-2-
http://www.thecableco.com/Product/XLR-M-XLR-Connector--Set-of-2- -
Congrats on the new speakers. I hope you have a big room for those bad boys, They aren't much bigger than the 2.3's but it would be interesting to hear you impressions on the differences once they are all done.
My Father went from stock 2.3's to fully modded 1.2TL's...both great speakers IMO.
