Mit cvt2

acmf74
acmf74 Posts: 936
edited June 2012 in 2 Channel Audio
Has anyone have any experience with this interconnect?
Post edited by acmf74 on
· Share on FacebookShare on Twitter

Comments

  • heiney9
    heiney9 Posts: 25,165
    edited January 2012
    http://www.polkaudio.com/forums/showthread.php?115800-MIT-CVT-1-Cable-Demo-Review-Round-3&highlight=mit+demo

    This should help, all kinds of reviews.

    H9
    "Appreciation of audio is a completely subjective human experience. Measurements can provide a measure of insight, but are no substitute for human judgment. Why are we looking to reduce a subjective experience to objective criteria anyway? The subtleties of music and audio reproduction are for those who appreciate it. Differentiation by numbers is for those who do not".--Nelson Pass Pass Labs XA25 | EE Avant Pre | EE Mini Max Supreme DAC | MIT Shotgun S1 | Pangea AC14SE MKII | Legend L600 | BlueSound Node 3 - Tubes add soul!
    · Share on FacebookShare on Twitter
  • Drenis
    Drenis Posts: 2,871
    edited January 2012
    ^ He asked about CVT2 not CVT1.
    · Share on FacebookShare on Twitter
  • heiney9
    heiney9 Posts: 25,165
    edited January 2012
    Drenis wrote: »
    ^ He asked about CVT2 not CVT1.

    Pretty much identical unless you are into splitting hairs. I bet most couldn't tell the difference so I think the descriptions provided in the demo program will be very close if not spot on as to what he can expect.

    H9
    "Appreciation of audio is a completely subjective human experience. Measurements can provide a measure of insight, but are no substitute for human judgment. Why are we looking to reduce a subjective experience to objective criteria anyway? The subtleties of music and audio reproduction are for those who appreciate it. Differentiation by numbers is for those who do not".--Nelson Pass Pass Labs XA25 | EE Avant Pre | EE Mini Max Supreme DAC | MIT Shotgun S1 | Pangea AC14SE MKII | Legend L600 | BlueSound Node 3 - Tubes add soul!
    · Share on FacebookShare on Twitter
  • acmf74
    acmf74 Posts: 936
    edited January 2012
    Currently my IC's are SC analog 2s and will be getting MIT CVT-2 ICs this week. Where should I place the MITs to utilize them the most? Between the CDP/preamp or the preamp/amp?
    · Share on FacebookShare on Twitter
  • F1nut
    F1nut Posts: 50,561
    edited January 2012
    Try both, but keep in mind that MIT cables perform best when all are the same, including speaker cables.
    Political Correctness'.........defined

    "A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a t-u-r-d by the clean end."

    President of Club Polk

    · Share on FacebookShare on Twitter
  • fjross
    fjross Posts: 183
    edited January 2012
    I am in a similar situation, I had to cap the budget at speaker and (1) pair of interconnects. Joe from Equess recomended the higher quality cables between the cd and preamp. I'm waiting for the Shotgun 3.3s to arrive early next week.
    Mcintosh MC-501 mono blocks
    Mcintosh C-45
    Mcintosh MVP-871
    PS AUDIO AV5000
    MIT 3.3 Shotgun biwire speaker interface
    MIT 3.3 Shotgun XLR interconnects
    Polk 2.3TL's Gimpod boards/F-1 modded crossovers/dynamat/JB weld/Larry's rings/Blackhole 5 strips
    Polk 3.1 TL's mint/stock (purchased new)
    Polk SDA-2's
    · Share on FacebookShare on Twitter
  • acmf74
    acmf74 Posts: 936
    edited June 2012
    Zero wrote: »
    Yep. Running a full assortment of CVT-2's at the moment.

    Zero. I'm thinking of doing the same. How do you like them?
    · Share on FacebookShare on Twitter