Question regarding Monitor 70 hookup (newbie to wiring/setup)

enforcer2133
enforcer2133 Posts: 2
Hello folks - I have a noob question. I just got my first non-HTIB setup with Monitor 70s, a CS2 and an Onkyo receiver. Just going with those for now until I get surrounds at a later time.

My question is, I noticed the Monitor 70s have 4 binding posts on each speaker, not 2 like I'm used to. Am I supposed to be using all 4 posts or just the top two for now and the other two later, if I b-amp or whatever. Don't be cruel, if you feel it's a dumb/obvious question.
Post edited by enforcer2133 on

Comments

  • tonyb
    tonyb Posts: 32,983
    edited November 2011
    The back of the speaker has a brass plate connecting the two pairs of posts, leave those on, connect your speaker wire to either the top or bottom set of posts and your done. Don't even mess with bi-amping from a receiver, waste of time and money.
    HT SYSTEM-
    Sony 850c 4k
    Pioneer elite vhx 21
    Sony 4k BRP
    SVS SB-2000
    Polk Sig. 20's
    Polk FX500 surrounds

    Cables-
    Acoustic zen Satori speaker cables
    Acoustic zen Matrix 2 IC's
    Wireworld eclipse 7 ic's
    Audio metallurgy ga-o digital cable

    Kitchen

    Sonos zp90
    Grant Fidelity tube dac
    B&k 1420
    lsi 9's
  • karib
    karib Posts: 4
    edited November 2011
    I hope its OK to piggyback on enforcer2133's question but I'm a noob too and this post is the closes I've found searching the forum to my possibly noob question. I'm receiving a pair of Monitor 70s later today and I was wondering if I could use an Onkyo HT-R380 and a TX-8255 to bi-amp these speakers? What are the chances of running them parallel (if this is possible)? Maybe its just a bad idea. In the words of someone wiser than me ... "Don't be cruel, if you feel it's a dumb/obvious question."
  • nguyendot
    nguyendot Posts: 3,594
    edited November 2011
    Don't use two receivers. Use one.

    You can try - it's all part of the learning process, but the gain on the two receivers is different. When you bi-amp you want to use two dedicated amplifiers, not receivers.
    Main Surround -
    Epson 8350 Projector/ Elite Screens 120" / Pioneer Elite SC-35 / Sunfire Signature / Focal Chorus 716s / Focal Chorus CC / Polk MC80 / Polk PSW150 sub

    Bedroom - Sharp Aquos 70" 650 / Pioneer SC-1222k / Polk RT-55 / Polk CS-250

    Den - Rotel RSP-1068 / Threshold CAS-2 / Boston VR-M60 / BDP-05FD
  • nwohlford
    nwohlford Posts: 700
    edited November 2011
    karib wrote: »
    I hope its OK to piggyback on enforcer2133's question but I'm a noob too and this post is the closes I've found searching the forum to my possibly noob question. I'm receiving a pair of Monitor 70s later today and I was wondering if I could use an Onkyo HT-R380 and a TX-8255 to bi-amp these speakers? What are the chances of running them parallel (if this is possible)? Maybe its just a bad idea. In the words of someone wiser than me ... "Don't be cruel, if you feel it's a dumb/obvious question."

    You can try biamping if you are curious, but do not attempt to put the two receivers in parallel.
  • karib
    karib Posts: 4
    edited November 2011
    nwohlford wrote: »
    You can try biamping if you are curious, but do not attempt to put the two receivers in parallel.
    Thanks
  • Tour2ma
    Tour2ma Posts: 10,177
    edited December 2011
    tonyb wrote: »
    Don't even mess with bi-amping from a receiver, waste of time and money.
    Not even if it takes very little of either... :cool:
    More later,
    Tour...
    Vox Copuli
    Better to remain silent and be thought a fool, than to open your mouth and remove all doubt. - Old English Proverb

    "Death doesn't come with a Uhaul." - Dennis Gardner

    "It's easy to get lost in price vs performance vs ego vs illusion." - doro
    "There is a certain entertainment value in ripping the occaisonal (sic) buttmunch..." - TroyD