3.1tl problem

bluecomet
bluecomet Posts: 1,118
edited May 2011 in Vintage Speakers
Moving my 3.1tl speakers around with the interconnect cable still attached, I banged into it and snapped the IC pin in the speaker. Anyone have any ideas on how to get the pin out. Ben you have a PM because I think it is wedged and the part may have to be replaced in the speaker. Any suggestions would be appreciated.
Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
Yamaha RX-V2500 System, Carver A753 3 channel amp.

Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
Post edited by bluecomet on
· Share on FacebookShare on Twitter

Comments

  • Toolfan66
    Toolfan66 Posts: 17,339
    edited May 2011
    Is this an original SDA cable you were using?? also if memory serves me right you should be able to take out the passive and push the pin out from the back side with a smaller pin, you might have to remove some hot glue to get to it.. If you need a new socket I have one here with your name on it..
    Polk Audio SDA 2.3tl Fully Hot Rodded. 😎

    SVS SB16 X2

    Cary SLP-05/Ultimate Upgrade.
    Cary SA-500.1 ES Amps
    Cary DMS 800PV Network
    OPPO UDP 205/ModWright Modification
    VPI Scout TT / Dynavector 20x2
    Jolida JD9 Fully Modified

    VPI MW-1 Cyclone RCM

    MIT Shotgun 3 cables throughout / Except TT, and PC’s
    · Share on FacebookShare on Twitter
  • bluecomet
    bluecomet Posts: 1,118
    edited May 2011
    It was one of Ben's silver cables. I have a feeling I will need the new socket. Thanks for the offer.
    Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
    Yamaha RX-V2500 System, Carver A753 3 channel amp.

    Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

    Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
    · Share on FacebookShare on Twitter
  • bluecomet
    bluecomet Posts: 1,118
    edited May 2011
    Does anyone have an extra pin/blade socket? Looks like I going need it.
    Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
    Yamaha RX-V2500 System, Carver A753 3 channel amp.

    Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

    Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
    · Share on FacebookShare on Twitter
  • Toolfan66
    Toolfan66 Posts: 17,339
    edited May 2011
    Sorry blue it will go out Monday !!!!
    Polk Audio SDA 2.3tl Fully Hot Rodded. 😎

    SVS SB16 X2

    Cary SLP-05/Ultimate Upgrade.
    Cary SA-500.1 ES Amps
    Cary DMS 800PV Network
    OPPO UDP 205/ModWright Modification
    VPI Scout TT / Dynavector 20x2
    Jolida JD9 Fully Modified

    VPI MW-1 Cyclone RCM

    MIT Shotgun 3 cables throughout / Except TT, and PC’s
    · Share on FacebookShare on Twitter
  • bluecomet
    bluecomet Posts: 1,118
    edited May 2011
    Thanks. I really appreciate it.
    Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
    Yamaha RX-V2500 System, Carver A753 3 channel amp.

    Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

    Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
    · Share on FacebookShare on Twitter
  • Vette C6.r
    Vette C6.r Posts: 1,560
    edited May 2011
    As I recall Ben's IC only has the pin portion. In the pin/blade you only need the pin.
    · Share on FacebookShare on Twitter
  • bluecomet
    bluecomet Posts: 1,118
    edited May 2011
    Thait is correct.
    Polk HT system 1: LSIC, LSI25 mains, LSI F/X rears, Lsi F/X rear centers,
    Yamaha RX-V2500 System, Carver A753 3 channel amp.

    Polk HT system 2: , SRT system with f/x 1,000's rear speakers on 7.1 system currently using Onkyo TX-RZ820 receiver, powered by Sunfire Grand Theater amp

    Polk Speaker collection: SDA SRS 1.2tl x 2, SRT system, SDA SRS 2 P/B, SDA 2A, SDA 1C Studio, SDA CRS+, Monitor 7B & 4, SRS 3.1tl, RTA 15tl, LS90, LSI 9
    · Share on FacebookShare on Twitter