Monitor 10b XO board

Jack A
Jack A Posts: 77
edited April 2011 in Vintage Speakers
To All, Does any one know if the Monitor 10b xo boards are still available from Polk Audio?
I am doing a xo upgrade and I found one of the corner holes is broken.
I would like to replace the board....see attached pic.:confused:
Clarajack
Post edited by Jack A on
· Share on FacebookShare on Twitter

Comments

  • Vette C6.r
    Vette C6.r Posts: 1,560
    edited April 2011
    No they don't.

    Keep an eye on E-Bay. Currently there are a couple for the Monitor 5 and 7. The 10's do come on from time to time. Just keep checking back on E-Bay.
    · Share on FacebookShare on Twitter
  • TennMan
    TennMan Posts: 1,266
    edited April 2011
    Jack A wrote: »
    To All, Does any one know if the Monitor 10b xo boards are still available from Polk Audio?
    I am doing a xo upgrade and I found one of the corner holes is broken.
    I would like to replace the board....see attached pic.:confused:
    Jack, if you are talking about the hole for the plastic stand off I don't see that as being a problem, unless there is damage underneath that we can't see. I would get the appropriate sized fiber washer to go over the stud and it should hold the board in place. Just my 2?.
    • SDA 2BTL · Sonicaps · Mills resistors · RDO-198s · New gaskets · H-nuts · Erse inductors · BH5 · Dynamat
    • Crossover upgrades by westmassguy
    • Marantz 1504 AVR (front speaker pre-outs to Adcom 555)
    • Adcom GFA-555 amp · Upgrades & speaker protection added by OldmanSRS
    • Pioneer DV-610AV DVD/CD player
    • SDA CRS+ · Hidden away in the closet
    · Share on FacebookShare on Twitter
  • Jack A
    Jack A Posts: 77
    edited April 2011
    Hi Ronnie, Good idea about the washer this was done my Polk. I saw this when I opened the xo for the first time.
    Did you received my pic of the Vampire binding post installation and fuse removal?
    Jack
    Clarajack
    · Share on FacebookShare on Twitter
  • Jack A
    Jack A Posts: 77
    edited April 2011
    Thanks for the tip.
    Clarajack
    · Share on FacebookShare on Twitter
  • TennMan
    TennMan Posts: 1,266
    edited April 2011
    Jack A wrote: »
    Hi Ronnie, Good idea about the washer this was done my Polk. I saw this when I opened the xo for the first time.
    Did you received my pic of the Vampire binding post installation and fuse removal?
    Jack
    Didn't get the photos Jack.
    • SDA 2BTL · Sonicaps · Mills resistors · RDO-198s · New gaskets · H-nuts · Erse inductors · BH5 · Dynamat
    • Crossover upgrades by westmassguy
    • Marantz 1504 AVR (front speaker pre-outs to Adcom 555)
    • Adcom GFA-555 amp · Upgrades & speaker protection added by OldmanSRS
    • Pioneer DV-610AV DVD/CD player
    • SDA CRS+ · Hidden away in the closet
    · Share on FacebookShare on Twitter
  • Jack A
    Jack A Posts: 77
    edited April 2011
    Ronnie, I did a upgrade from Vista to Windows 7 and have had nothing but problems.

    I'll try again when I find out whats wrong.

    JAck
    Clarajack
    · Share on FacebookShare on Twitter
  • Joe08867
    Joe08867 Posts: 3,919
    edited April 2011
    Looking at that original pic i can't see why it would cause a problem. It is on the outside edge of the board where there is no wire imprint. Can you disconnect the board so we can see the other side?
    · Share on FacebookShare on Twitter
  • Joe08867
    Joe08867 Posts: 3,919
    edited April 2011
    moshun111 reported^^
    · Share on FacebookShare on Twitter
  • Jack A
    Jack A Posts: 77
    edited April 2011
    Joe08867, Your right this is the way it came 28 years from Polk. should not be a problem.
    Clarajack
    · Share on FacebookShare on Twitter
  • Joe08867
    Joe08867 Posts: 3,919
    edited April 2011
    I had a feeling I was right. It's nice to get confirmation. Have fun with the upgrade!!!!
    · Share on FacebookShare on Twitter