CRS speaker stands
hoosier21
Posts: 4,413
I did a search, didn't find what I needed, ok I am lazy also.
There is a post on this forum showing the dimensions of the stands Polk sold with these speakers.
Can anyone find it? Or hell if you have a set, can you post the dimensions.
Thanks
There is a post on this forum showing the dimensions of the stands Polk sold with these speakers.
Can anyone find it? Or hell if you have a set, can you post the dimensions.
Thanks
Dodd - Battery Preamp
Monarchy Audio SE100 Delux - mono power amps
Sony DVP-NS999ES - SACD player
ADS 1230 - Polk SDA 2B
DIY Stereo Subwoofer towers w/(4) 12 drivers each
Crown K1 - Subwoofer amp
Outlaw ICBM - crossover
Beringher BFD - sub eq
Where is the remote? Where is the $%#$% remote!
"I've always been mad, I know I've been mad, like the most of us have...very hard to explain why you're mad, even if you're not mad..."
Monarchy Audio SE100 Delux - mono power amps
Sony DVP-NS999ES - SACD player
ADS 1230 - Polk SDA 2B
DIY Stereo Subwoofer towers w/(4) 12 drivers each
Crown K1 - Subwoofer amp
Outlaw ICBM - crossover
Beringher BFD - sub eq
Where is the remote? Where is the $%#$% remote!
"I've always been mad, I know I've been mad, like the most of us have...very hard to explain why you're mad, even if you're not mad..."
Post edited by RyanC_Masimo on
Comments
-
This what you were looking for?
http://clubpolk.polkaudio.com/forum/showthread.php?s=&threadid=5163&highlight=sda+crs%2A+stands -
I'd say that's it. Good job.
While we're on the subject. Anybody know the dimensions of the original Monitor 10 stands?Make it Funky!
-
Are these them? Not sure if these are Polk stands, but that is what I have with my Monitor 10's.
-
Could be, but I'm not certain. Is there a slope to them? Could you measure them up whenever you get a chance? No hurry though as I have many projects on my plate at the moment.
Thanks!Make it Funky! -
My god thats a crappy pic, even for my crappy camera.
I sincerely appologize for that
There is a slope to them.
I will take some measurements in the morning and report back to you.
Mike -
Mark,
Here's an excellent replacement (I consider it an upgrade) stand for the Monitor 10's. The pic doesn't show it, but they have a 20 degree angle on the top plate. There is an 8" and 12" version.
http://accessories4less.com/aless4/Corporate/itemdesc.asp?CartId=12177125HCDXJ-ACCWARE-85&ic=SD%2DBB50%2F8&cc=&tpc=
Cheers,
RussCheck your lips at the door woman. Shake your hips like battleships. Yeah, all the white girls trip when I sing at Sunday service. -
Hoosier,
You used to have two sets of stands... you sold me one and God knows what you did with the other. What's going on? Speaker-confusiciousness?
Just Curious. -
I sold the other set to somebody on here a long time ago.
I have a set of CRS+'s and was thinking of making a a pair of stands from wood. Or maybe even having a set made for me out of square tube.Dodd - Battery Preamp
Monarchy Audio SE100 Delux - mono power amps
Sony DVP-NS999ES - SACD player
ADS 1230 - Polk SDA 2B
DIY Stereo Subwoofer towers w/(4) 12 drivers each
Crown K1 - Subwoofer amp
Outlaw ICBM - crossover
Beringher BFD - sub eq
Where is the remote? Where is the $%#$% remote!
"I've always been mad, I know I've been mad, like the most of us have...very hard to explain why you're mad, even if you're not mad..." -
Thanks Mike. Overall measurements would be fine as if I build them I'll make them a little different.
Thanks Russman. Those look much better than what I'll probably end up with. I bookmarked it just in case I get frustrated.Make it Funky! -
Hey Gidrah-
Sorry bro forgot about this altogether.
Here ya go-
The top plate:
Is 8 9/16" x 9 13/16"
by 1/2" thick.
The two little supports (vertical) are:
5" x 5 11/16" at the higher end, by 3/4" thick and spaced 15/16" apart.
The bottom plate:
11 10/16" x 11 10/16" by 3/4" thick.
The top plate sits 1 1/2" back on the vertical supports.
If you need anything else, post here or I have AIM, Surfbum072.
Take it easy. Mike -
