CS 350 LS
Options
xjghost
Posts: 1,084
Looking for a driver for my CS350 center. One appears to have magnetic shifted. 3 of the 4 move and one is locked up. Any help would be appreciated. Haven’t pulled it to see what the number is.
HT/2Channel: Emotiva MMC-1, Adcom GFA-555II, Polk SDA 3.1's, Teac TN-300 TT, Polk Center and Sub.
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's
Comments
-
I'll check the boneyard tomorrow morning. Where are you located in the event that I have any spares?
-
South Carolina. Gladly pay for it and shipping.HT/2Channel: Emotiva MMC-1, Adcom GFA-555II, Polk SDA 3.1's, Teac TN-300 TT, Polk Center and Sub.
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's -
Well it appears that I do have a few of these in the parts bin. Please verify that the model number is the same. I apologize for the driver being so dusty, they have been stored for several years.
-
Ok pulled the driver. And it’s a 4802. Maybe I need to pull the others and confirm.HT/2Channel: Emotiva MMC-1, Adcom GFA-555II, Polk SDA 3.1's, Teac TN-300 TT, Polk Center and Sub.
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's -
HT/2Channel: Emotiva MMC-1, Adcom GFA-555II, Polk SDA 3.1's, Teac TN-300 TT, Polk Center and Sub.
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's -
I'll check to see if I have any drivers matching your 4802 tomorrow. Hopefully we'll have a match.
-
Well I checked the other 3 drivers that I have and they're all 4850's.
I'm not sure if they're interchangeable. Perhaps someone with more knowledge on the subject can chime in. -
Buy this OR look for better deals & have spare parts..
..
..
Randy/Maine -
-
-
MW4850 is the correct driver for the CS350. Both of mine have the same drivers Jose.
All mine look just like this.
[/img]
-
Ivan is there a difference between cs350 n cs350ls ? I don't know much about them..
..
..
Randy/Maine -
They were part of the LS series so no.
Cs350/cs350ls are the same speaker -
Got ya. Thx. I tried researching it earlier. But gave up. Heck I can't remember what MWs are in my cs1000p they may even be same. Not much info out there..
..
..
Randy/Maine -
I looked on eBay last night and didn't find that one. I did find hole speakers though. Hence coming here. Oh well Ordered one just now off eBay.HT/2Channel: Emotiva MMC-1, Adcom GFA-555II, Polk SDA 3.1's, Teac TN-300 TT, Polk Center and Sub.
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's -
Ok so this one speaker will not move while the others do. I assumed a magnet shifted but in an effort to learn here from what I remember a speaker has a part that "floats" inside and the movement makes the sound. I know over simplified. So I guess the voice coil lost it's ability to move. Any thoughts on what is going on with this one speaker?HT/2Channel: Emotiva MMC-1, Adcom GFA-555II, Polk SDA 3.1's, Teac TN-300 TT, Polk Center and Sub.
Bedroom system: Carver CT-24, Parasound HCA-800II, Monitor 10's
Additional projects: RTA 12c's -
Everything is aligned & once the magnet shifts or burns up the voice coils it is toasted..
..
..
Randy/Maine -
-
This is just speakers in general. I have a better diagram at home that shows & explains more in details. It is posted here on forum as well..
..
..
Randy/Maine
