Need Amplifier and Receiver advised for lsi15
Another question, is it better to go with lsi15 or lsi25?:cool:
Post edited by ray2per on
Comments
-
Hi Ray, welcome to Club Polk!
You have done your reading & have answered your own questions! All of the brands that you have mentioned will give you an outstanding system!
Best bang for the buck within your budget will be an Outlaw 990/7500/7700 system!
Most around here seem to prefer the 15's.
Oh & one more thing that you should work into your budget & system is a Subwoofer! Most around here prefer SVS.
Let us know what you get & post pictures!Marantz AV-7705 PrePro, Classé 5 channel 200wpc Amp, Oppo 103 BluRay, Rotel RCD-1072 CDP, Sony XBR-49X800E TV, Polk S60 Main Speakers, Polk ES30 Center Channel, Polk S15 Surround Speakers SVS SB12-NSD x2 -
Are you paying retail for your LSi15's? If so, that does not leave alot of money for an pre/pro and amp.
Does your current reciever have pre-out connections for all channels on the back of it. (It will be in the same area that the subwoofer connection is in) If it does, that will save you some cash for now and your job will be much easier. If it does not, it may be a little tougher.
Are you willing to purchased used or do you really want to stay with new. It is much easier to get a good deal used, but some really like the safety of purchasing new (and sometimes local) in case there are any issues.
As far as the 15's/25's question goes, I really like the 15's. The 25's will sound a little better if your amp is not quite up to snuff as the woofer on it is self powered. The 15's are the hardest of the LSi series to drive. (the 25's would be similar to the 9's in difficutly to drive)
I have heard the 25's in a in-home demo and just never was able to get the woofer dialed in correctly where you could hear it well, but it didn't call alot of attention to itself. I am sure it will be nice speaker, if you get through those challenges.
MichaelMains.............Polk LSi15 (Cherry)
Center............Polk LSiC (Crossover upgraded)
Surrounds.......Polk LSi7 (Gloss Black - wood sides removed and crossovers upgraded)
Subwoofers.....SVS 25-31 CS+ and PC+ (both 20hz tune)
Pre\Pro...........NAD T163 (Modded with LM4562 opamps)
Amplifier.........Cinepro 3k6 (6-channel, 500wpc@4ohms) -
Thanks for your reply cfrizz.
Mcloki, I'm planning to get the lsi15 off ebay.
I think my receiver has some preout connections for all channels. I will check it out.
Thanks again for your help I will be keep in touch with you for any questions and suggestions.
Victor -
MIchael, I would say that since a lot has changed in the 8 yrs since his receiver came out, it is time to upgrade that as well & he might as well go with separates!Marantz AV-7705 PrePro, Classé 5 channel 200wpc Amp, Oppo 103 BluRay, Rotel RCD-1072 CDP, Sony XBR-49X800E TV, Polk S60 Main Speakers, Polk ES30 Center Channel, Polk S15 Surround Speakers SVS SB12-NSD x2
-
cfrizz wrote:MIchael, I would say that since a lot has changed in the 8 yrs since his receiver came out, it is time to upgrade that as well & he might as well go with separates!
I would agree - it all comes down to budget.
With $3000 max to spend now -
$1200 for the speakers (as a guess, including shipping) That leaves about $1800 for the pre/pro.
If he went outlaw - he could get the 990 bstock for $1000. that would leave $800 for the amp. He could get a nice 5 channel amp like this one and then get a killer 2 channel amp later to run his 15's off of when he is ready to move to 7.1
When I asked my question though, I thought he was going to purchase new. The 15's would have run him $1800 (or so with tax) only leaving about $1200 for the amp and preamp. Now that I know he is willing to go used, I agree that his best option is to plan on ditching the AVR all together...
MichaelMains.............Polk LSi15 (Cherry)
Center............Polk LSiC (Crossover upgraded)
Surrounds.......Polk LSi7 (Gloss Black - wood sides removed and crossovers upgraded)
Subwoofers.....SVS 25-31 CS+ and PC+ (both 20hz tune)
Pre\Pro...........NAD T163 (Modded with LM4562 opamps)
Amplifier.........Cinepro 3k6 (6-channel, 500wpc@4ohms) -
Thank you all for your response.
I can probably stretch my budget up to $4,000 but I need to convinced my wife about that. She'll probably say yes. Just need to encouraged her about how great the speaker sound.
Victor -
I saw outlaw 750 on craigslist for $600. Is that a good amplifier for sli15? or should I consider the 7500 or the 7200?
Victor -
Hi Victor. You should hold out for the 7500 or the 7200 since those are 200wpc & the 750 is only 165wpc!
The LSI's need all the power you can throw at them & ask for more!Marantz AV-7705 PrePro, Classé 5 channel 200wpc Amp, Oppo 103 BluRay, Rotel RCD-1072 CDP, Sony XBR-49X800E TV, Polk S60 Main Speakers, Polk ES30 Center Channel, Polk S15 Surround Speakers SVS SB12-NSD x2 -
i would keep the rubber side down and the metal side up after that anything goes.
Welcome to Club Polk, enjoy the fun, its a truly great place to hang.
RT1 -
Is Klipsch RF7 comparable to lsi15?
Are they really closed on the way they sound?
Just getting some feedback. I love polk by the way.
Victor -
ray2per wrote:Is Klipsch RF7 comparable to lsi15?
Are they really closed on the way they sound?
Just getting some feedback. I love polk by the way.
Victor
Two totally different worlds here. If you love the Polk LSi's, you'll hate the brightnes/harshness of the Klipsch's, INMO.
Mike -
Hi!
I am also looking for a pair of LSi15 speakers. Where can you get the cheapest deal? Can anybody help?
Thanks. -
Keep an eye on craigslist guys, if you aren't in a hurry.
Here in Minneapolis there is a pair of Lsi15's and a LsiC listed for 1200. I've usually found that these prices can be negotiated in my experience.
I picked up a nice parasound 1205a for 300 about 4 months ago. -
Keep an eye on craigslist guys, if you aren't in a hurry.
Here in Minneapolis there is a pair of Lsi15's and a LsiC listed for 1200. I've usually found that these prices can be negotiated in my experience.
I picked up a nice parasound 1205a for 300 about 4 months ago.
WHat do you guys think about a Sherwood Newcastle AM-9080 5-channel Power Amp 120 watts/ channel at 8 ohms 175 watts/chan. at 4 ohms....will that be a good amp to power the 15'sTV:Sony Bravia XBR4 52'
Mains: Lsi m 705
C:Lsi m 706
Rears: Lsi m 703
Sub: Epik Empire
Pre:Marantz AV 7005
Amp:Sunfire TGA-7400
Blueray: Opp 93
A/V Component: Panamax M5100-PM
Cables: Signal Cable, White Zombie, MIT, Pepster's power cables -
bdtae5656,
Absolutely not.
You can pick up an Outlaw 990 these days for nothing (the 997s are coming out soon, and people are unloading their 990s). Then pour your money into an Outlaw 7500. I don't post here much, but I've owned a pair of Lsi15s for several years. I think the Outlaw 7500 amp, with 200wpc is about ideal. The Lsi15s are incredibly inefficient. I'm not criticizing them--they're amazing speakers for the price--but if you are going to buy Lsi15s you need to allocate solid money for an amplifier. If I could do it over again, I would not have wasted my money on the POS 120 wpc reciever I bought at the time. As a matter of fact, I think my Lsi15s would do even better with 350 wpc of power. Seriously. The more power you throw at them, the better their dynamics get. They are fantastic speakers.
Monty -
Yeah - the LSI series are amazing speakers - but you really need to find an amp that is rated minimum 200wpc into 8 ohms that also does 4 ohms. I know they're 4 ohm speakers, but most amps at a glance list 8 ohm power. If it's rated for 4 ohm play, and does at least 200wpc into 8 ohms, then it should have enough power to run plenty into 4 ohms. Does that make sense?
Also - are you looking into picking up an LSIc now? Or are you going to go with the phantom center? If you're planning on picking up a center now, then you need at least a 3 channel amp. If not, then getting a 2 channel now would work and picking up a 5 channel when you add other speakers should suffice. But i think i'd personally recommend using the same amp for your front 3 to have as close to the same sound as possible.
So going with something like...
Outlaw Monoblocks - I've heard they work great with the LSI line
Acurus 200x3 - Good 3 Channel amp - what my buddy is using for his LSI 9s and LSIc - and this is a good price at Audiogon
Adcom GFA-5503 - Another good 3 channel
Or you could, as stated earlier, go 5 channel now and take the bulk of the expense away only needing a two channel later (and not incredibly powerful at that) to take care of surrounds (though the earlier poster suggested more power to teh fronts later). For that, you could go something like...
Sunfire TGA-5200 - Would be perfect for a 5.1 LSI setup, though it looks like the sale is pending already
Rotel RMB-1095 - would also be perfect for your LSI speakers
And really - there are plenty of great options out there.
As far as your receiver - there are also a ton of great relatively inexpensive options with current HT settings and connections that will do. Just make sure they have pre-outs. I picked up a brand new Onkyo TX-SR806 for under $600. There are also offerings from many other companies in the same price range. I guess if you wanted to, there are more expensive routes to go with it - but i'm all about bang for buck and this would get you in under your 3k budget.
Good luck!Not my setup - but what I have put together for a friend (i.e. what mine would be if i had the money to invest
)
Front: 2 x LSI-9
Center: LSI-C
Rear: 4 x M10
Sub: Elemental Design A2-300
AVR: Onkyo TX-SR806
Amp: Acurus 200x3
BD: HTPC
Television Programming: Dish ViP722
Video: Epson 6500UB Front Projector
If you're ever in St. Louis on a Sunday morning, come join us at the Hazelwood church of Christ for worship! -
candjhuntley wrote: »Yeah - the LSI series are amazing speakers - but you really need to find an amp that is rated minimum 200wpc into 8 ohms that also does 4 ohms. I know they're 4 ohm speakers, but most amps at a glance list 8 ohm power. If it's rated for 4 ohm play, and does at least 200wpc into 8 ohms, then it should have enough power to run plenty into 4 ohms. Does that make sense?
Also - are you looking into picking up an LSIc now? Or are you going to go with the phantom center? If you're planning on picking up a center now, then you need at least a 3 channel amp. If not, then getting a 2 channel now would work and picking up a 5 channel when you add other speakers should suffice. But i think i'd personally recommend using the same amp for your front 3 to have as close to the same sound as possible.
So going with something like...
Outlaw Monoblocks - I've heard they work great with the LSI line
Acurus 200x3 - Good 3 Channel amp - what my buddy is using for his LSI 9s and LSIc - and this is a good price at Audiogon
Adcom GFA-5503 - Another good 3 channel
Or you could, as stated earlier, go 5 channel now and take the bulk of the expense away only needing a two channel later (and not incredibly powerful at that) to take care of surrounds (though the earlier poster suggested more power to teh fronts later). For that, you could go something like...
Sunfire TGA-5200 - Would be perfect for a 5.1 LSI setup, though it looks like the sale is pending already
Rotel RMB-1095 - would also be perfect for your LSI speakers
And really - there are plenty of great options out there.
As far as your receiver - there are also a ton of great relatively inexpensive options with current HT settings and connections that will do. Just make sure they have pre-outs. I picked up a brand new Onkyo TX-SR806 for under $600. There are also offerings from many other companies in the same price range. I guess if you wanted to, there are more expensive routes to go with it - but i'm all about bang for buck and this would get you in under your 3k budget.
Good luck!
I ended up going with LSI C/LSI 25's with a Emo XPA-3TV:Sony Bravia XBR4 52'
Mains: Lsi m 705
C:Lsi m 706
Rears: Lsi m 703
Sub: Epik Empire
Pre:Marantz AV 7005
Amp:Sunfire TGA-7400
Blueray: Opp 93
A/V Component: Panamax M5100-PM
Cables: Signal Cable, White Zombie, MIT, Pepster's power cables -
Very nice! You won't be disappointed. Be sure to let us all know what you think of them
Have you thought through your options on a receiver yet?Not my setup - but what I have put together for a friend (i.e. what mine would be if i had the money to invest
)
Front: 2 x LSI-9
Center: LSI-C
Rear: 4 x M10
Sub: Elemental Design A2-300
AVR: Onkyo TX-SR806
Amp: Acurus 200x3
BD: HTPC
Television Programming: Dish ViP722
Video: Epson 6500UB Front Projector
If you're ever in St. Louis on a Sunday morning, come join us at the Hazelwood church of Christ for worship! -
candjhuntley wrote: »Very nice! You won't be disappointed. Be sure to let us all know what you think of them
Have you thought through your options on a receiver yet?
I went ahead and opened the box to my HK 3550....What im going to do diff is run Rca/optical to the Cable box and see if that helps out! When the 25's get here I'll diff let you know. Whats a good rear speaker to run off my HK until I get a rear ampTV:Sony Bravia XBR4 52'
Mains: Lsi m 705
C:Lsi m 706
Rears: Lsi m 703
Sub: Epik Empire
Pre:Marantz AV 7005
Amp:Sunfire TGA-7400
Blueray: Opp 93
A/V Component: Panamax M5100-PM
Cables: Signal Cable, White Zombie, MIT, Pepster's power cables -
i got my lsi15's for 1500 shipped from amazon, im using a rotel 1095 5 ch amp at 330wpc at 4ohms to drive them and my lsic and fx which i got for 1700. I have the amp connected to a pioneer sc05 which i got for 1000 from best buy a couple of weeks ago. Thats a total of 4200 not including the my sub center and rear speakers. The sound is AMAZING to say the least, absoutly spectacular.
-
candjhuntley wrote: »Very nice! You won't be disappointed. Be sure to let us all know what you think of them
Have you thought through your options on a receiver yet?
Ok I just got my 25's in the mail today from polk audio's refurb center! They look brand spanking new...for half the cost of what they would of been brand new. I cant tell you what they sound like yet.....that'll be tonight! I highly recommend if your looking or thinking refurb....diff do it! I cant tell the differenceTV:Sony Bravia XBR4 52'
Mains: Lsi m 705
C:Lsi m 706
Rears: Lsi m 703
Sub: Epik Empire
Pre:Marantz AV 7005
Amp:Sunfire TGA-7400
Blueray: Opp 93
A/V Component: Panamax M5100-PM
Cables: Signal Cable, White Zombie, MIT, Pepster's power cables -
Buy Polk Refurbs, they sound just as good as new. Buy from Polk of course!

